Search results

  1. alldodge

    1996 seadoo gti

    Note sure what it is, might be a oil injection check valve, but again I'm guessing
  2. alldodge

    Help with prop?

    Don't think you will get much better top end Could go to a 10 pitch if you can find it, but don't think it will be much better
  3. alldodge

    1996 seadoo gti

    Yes, BUT (note the but) You need a valve to keep water OFF until motor starts, "then" turn water ON Do in reverse to shut down
  4. alldodge

    Not starting

    It's most likely a diode in line with the ALT (alternator) During starting the Yel/Red wire from the key sends power to the FP relay and turns on the pump. The pump fills the carb and motor starts Once running the Yel/Red lead turns OFF the FP relay and what should happen is the ALT sends...
  5. alldodge

    Not starting

    Being a 999 and have a carb sounds like a GL. What model GL is it?
  6. alldodge

    1996 seadoo gti

    Yes, it has the quick connect garden hose male end Attach hose, and "Make sure to do it as listed above"
  7. alldodge

    25 EFI fuel pump not work

    I have no clue maybe someone else does
  8. alldodge

    1996 seadoo gti

    Need to see pics
  9. alldodge

    1993 OMC 5.8 EFI Idle problem, runs on throttle, too rich

    Fuel pressure is good and no fuel in hose, so those items are not the problem Need to see if there are any codes. OMC is a type that other scanners may not work. I'm no expert but we have yet to find what's causing the issue On top of the VST there is a line that goes to the intake. If the...
  10. alldodge

    1987 Bayliner Capri 1950 OMC Cobra bowrider starter bolt broke off.

    I'd pull the motor
  11. alldodge

    Monterey 275 SY

    I would say if you normally run heavy (friends onboard) then stick with the props If friends don't come often and your ok with being able to take off a little slower, then the 22's will drop WOT to around 4800. Cruising at 3800 or 3600 will not change the fuel burn and the motor has no issue...
  12. alldodge

    FourStroke 75 ELPT / 6 Beeps / New Boater

    Welcome Found your issue in another forum https://hotspotoutdoors.com/forums/topic/101835-mercury-6-beeps-fixed-fyi/page/2/
  13. alldodge

    1996 seadoo gti

    Look at the stern next to the nozzle, there is a hose connection. Attach hose with a shut off valve. Start motor then turn water ON To shut down, turn water OFF then kill motor
  14. alldodge

    1993 OMC 5.8 EFI Idle problem, runs on throttle, too rich

    Test fuel pressure 31-39 psi Check the vacuum hose coming from regulator to see if fuel is present
  15. alldodge

    Monterey 275 SY

    At 3800 rpm your slip is 27%, not great but typical for a heavy cruiser S/N shows as Scott mentioned 5000 is max WOT and should have no issues turning it If slip is decreased so will max WOT
  16. alldodge

    Alfa 1 gen 2 sterndrive install issues

    It either was not pushed into the coupler or the coupler is stripped Are there any teeth on the coupler?
  17. alldodge

    Alfa 1 gen 2 sterndrive install issues

    What does it look like when pushed in and pulled straight out, are there spline marks?
  18. alldodge

    Old 488 replacement idea

    Hey @Bondo or @Bt Doctur
  19. alldodge

    Alfa 1 gen 2 sterndrive install issues

    You should not turn bar with your fingers to see marks, it's just push in and pull out It does not appear the tool is going into the coupler, otherwise there would be marks if not turned, or cleaned off if rotated while inserted A new bearing is real tight. Alignment tool needs to be moved...
  20. alldodge

    I need help

    Serial number doesn't show TKS carb just regular carb (either 2 or 4bbl) and TBV ignition So many dealers (stealership) throw parts at a problem, charge for them and say it runs fine for us. They didn't listen to you and the problem, let's just throw some parts at it and call it good...
Top