Search results

  1. Scott Danforth

    . . . and I Thought Hi-tech Boat Engines Were Bad . . .

    Ted, thought of your thread as I'm chasing an HVAC issue in the daily whip that appears to be a bad BCM If I met an automotive controls engineer I'm going to throat punch him/her
  2. Scott Danforth

    Volvo penta 5.7 gxi 警報

    get a laptop with Rinda and plug in to look at the warnings.
  3. Scott Danforth

    2008 Rinker 296 Bowrider Vent Cover

    that vent cover is only available from Rinker. it was custom made by Rinker. your choices are find a used one on ebay, or buy one from Rinker, or make one out of fiberglass.
  4. Scott Danforth

    Best diy wax?

    better than collinite...... no. the white boats use collinite, however they have a crew of 20 somethings that start at the bow, polishing, buffing, waxing everything and sanding the teak. when they get to the stern, they start over.
  5. Scott Danforth

    2008 Rinker 296 Bowrider Vent Cover

    custom rinker only bit.
  6. Scott Danforth

    Malibu MMDC

    Throw it on fleabay
  7. Scott Danforth

    1976 collins craft.I have the boat off trailer and upside down.It has been washed with muritic acid.I am going to sand with 80 grit and use 2 part

    if you can paint and sand, you can re-spray the gel.
  8. Scott Danforth

    Mercruiser overheating

    you have a blockage or lack of flow from the pump
  9. Scott Danforth

    Building a '93 Caravelle 1750 Classic Bowrider

    spin the selector switch back and forth to clean the contacts. however it should be set to 1
  10. Scott Danforth

    1976 collins craft.I have the boat off trailer and upside down.It has been washed with muritic acid.I am going to sand with 80 grit and use 2 part

    You have a bit to go before you are worried about finish You need to grind back the broken areas and build back up with fiberglass You need to sand down the cracked gel down to good material, then fair and re-gel I wouldn't use epoxy paint unless it's rated for the job
  11. Scott Danforth

    Mercruiser overheating

    Did you find the bits missing from the old impeller?
  12. Scott Danforth

    1988 Rogue 2420

    The more we use the boat, the more things we find need work Hour meter quit sometime this year, courtesy lights quit working, NMEA gateway for fuel level quit working. Replaced anti-siphon. Need to redo the headliner and finish the closet and shelves
  13. Scott Danforth

    I freeze my block so you don't have to!

    20 degrees for 6 hours
  14. Scott Danforth

    Mercury Spanner wrench for tilt and trim

    $50 is dirt cheap.
  15. Scott Danforth

    Used Boat Lift question

    The motors are the cheapest part of a boat lift and the easiest to replace. Focus on the remainder. How new are the cables? Have the gear boxes been serviced? How are the uppers? How are the lowers? How are the sheaves?
  16. Scott Danforth

    Need RPM’s on 383MPI 1970 SeaRay 24’ project

    Also look at injector duty rate and
  17. Scott Danforth

    Winterization of my Commodore 272

    The 290DP was 1988, the DPA1 came out in 1989 ( updated 290 variant) Your 1996 would be a DPC1
  18. Scott Danforth

    What would cause my FSK16 to not be propelled by my Johnson JW10 3hp?

    Replace the impeller before worrying about the gear oil.
  19. Scott Danforth

    No data to vessel view mobile module

    The gateway is between the sensors and the gauges. In this case, most likely the ECM
  20. Scott Danforth

    Volvo AD41 non marine equivalent

    It's a marine engine only that shares a few things with the construction mitors
Top