Search results

  1. alldodge

    Back for a Visit!

    Howdy and welcome back
  2. alldodge

    Selling Newer Boat For Older Larger?

    I'm going the other direction, but nothing wrong with getting an older boat if its solid, but that's the question that must be determined. I've put 3 times what my current boat is worth but it is a boat
  3. alldodge

    Order enquiry and no response customer service

    Could use the "report" link maybe to get all the Mod's attention. Seems to work
  4. alldodge

    Maybe my turn for new boat time

    Got notification that boat is back on tract for completion 1st part of March, Yeah :D Don't know if that means a bit later then was first told or not, but either way I'm good
  5. alldodge

    Mercruiser 4.3 injection without any ignition

    Your original question listed in post one above, was posted again, word for word. It was reported to admins and Iboats admin removed it. I requested this thread be moved to the Mercruiser section so it would get more people looking at it which it was moved Agree, its hard to read. I have it...
  6. alldodge

    Mercruiser 4.3 injection without any ignition

    Reposting the same question(s) is not allowed. The only question which has not been answered "fully" is the complete wiring diagram. You said that you have manual 32 and if so the wiring is on page 4D-7
  7. alldodge

    Mercruiser 4.3 injection without any ignition

    MPI, motor needs to be scanned for codes When key is turned ON does the fuel pump run for a couple seconds and is there 2 beeps? Check for 5V on the Crankshaft position sensor (CPS) or any of the other sensors in the pic. Need to see exactly 5V with key ON motor OFF. If there is less then 5V...
  8. alldodge

    Mercruiser 4.3 injection without any ignition

    Welcome Look for the serial number on the motor. We need that to determine what ignition system you have. If serial number is not available, post a pic of the distributor and carb
  9. alldodge

    Quality kind a guy

    I've run into a couple guys that just love to kill things. Don't know if they did the same
  10. alldodge

    Have small 1100gph 12volt bilge pump - starts stops starts stops

    Tank is empty and the pump still runs, I would say its the float switch
  11. alldodge

    Another Bravo 3 shift issue

    If needed could just replace the upper
  12. alldodge

    Help !! Mercruiser Alpha 1 Generation 1 Power Steering Actuator

    Yes, I have removed one while installed. Don't have small hands but this is a BBC so not much room but got it done No expert but have not found any retro fitting needed. Remove old, install new and connect lines
  13. alldodge

    Help !! Mercruiser Alpha 1 Generation 1 Power Steering Actuator

    Could replace it with newer style but is costly. Used ebay one maybe?
  14. alldodge

    Help !! Mercruiser Alpha 1 Generation 1 Power Steering Actuator

    That is a Gen 2 Alpha, just the first run of the Gen 2's The steering actuator https://www.mercruiserparts.com/bam/subassembly/30858/1017/160 Serial number range 0D469859 to 0F679999 https://www.mercruiserparts.com/alpha-one-gen-ii-1991-1995-0d469859
  15. alldodge

    trailer surge

    CAT scales are calibrated monthly and accurate to 0.2% (10K = +/- 20 lb)
  16. alldodge

    trailer surge

    Maybe ask dealer service department their opinion
  17. alldodge

    Mercury

    Better MPG but weight is more, so top end is probably less. My guess is your not worried about top end
  18. alldodge

    trailer surge

    Guess I have nothing It has independent suspension and magnetic dampening, so might just be sensors, but might be wrong also. Anyway to turn off the ride support temporarily
  19. alldodge

    trailer surge

    I would guess the 700 tongue is a bit lighter. To find true tongue weight at a scale, disconnect trailer on the scale and have tongue on one pad and rear wheels on another. The folks at the scale will wait for you to set it up. This way you get true weight of all 3 points (Truck/Tongue/Trailer...
  20. alldodge

    Mini split outdoor condenser rodent guard advice

    Just a guess but are they getting in where the line set attaches? If so get the line set covers and seal it up Course steel wool also keeps them out
Top