Search results

  1. Scott Danforth

    Yamaha 150 ProV? Yay or Nay?

    mounting pattern was standardized in the 80's
  2. Scott Danforth

    At my wits end

    So what did you do on the motor? How did you "rebuild" the carbs? Did you do a link-n-sync? What is the compression numbers? What did you goober JB on (because that is never a repair) Have you checked your fuel for contamination?
  3. Scott Danforth

    Looking for advice!

    Most yacht owners ship their yachts on yacht express and fly vs sailing themselves.
  4. Scott Danforth

    Old archived posts

    @Bondo I would have deleted the guys post. Then again, we could probably agree that post should have been locked after Don's original response in post #2 Maybe a forum rule locking posts that are clearly against the safety standards of IMO / USCG Col Regs
  5. Scott Danforth

    Volvo fuel pump cross reference required.

    You can get the whole fuel assembly from Amazon. https://www.amazon.com/gp/product/B076Q9RG1R/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
  6. Scott Danforth

    Replacing my outdrive but can't determine the right one!

    Either a new SEI or a used 888
  7. Scott Danforth

    Looking for volvo pentum dp sm 1.95 lower unit hp

    Look on eBay for a used drive, or your local dealer. I don't see any damage in the pic. The drives are tough. Are you sure the drive is damaged?
  8. Scott Danforth

    Slop in DP290 power steering

    I was lucky to just find a cable to match the helm when I did mine a few years back
  9. Scott Danforth

    Which States/Provinces Enforce Registration Numbers Requirements

    Standard requirements for FL and WI
  10. Scott Danforth

    AQ125/270 Still overheating (PLEASE HELP)

    This says you have a blockage or the raw water casting has rotted off the pivot shaft
  11. Scott Danforth

    Old archived posts

    I'm flagging the zombie theads as fast as I can.......
  12. Scott Danforth

    SSC12412 steering cable

    Contact seastar and ask them about the replacment they can advise
  13. Scott Danforth

    Installing New OEM Egg Crate Foam for Engine Hatch?

    you are overthinking it. the project should have been done already had you just bought the dap and roller
  14. Scott Danforth

    Non-Skid Gelcoat Wearing Off?

    hard to tell. either you have crud in the crevices, or the gel is coming off. if the gel is coming off, simply mix up some gel with fumed silica and a bedliner roller and redo the non-skid.
  15. Scott Danforth

    Old archived posts

    newbies? or veteran grey beards?
  16. Scott Danforth

    Installing New OEM Egg Crate Foam for Engine Hatch?

    I would roll on the contact cement
  17. Scott Danforth

    Boat weight

    I would plan on digging a hole and turning it into a koi pond with the motor in it. the 153 cubic inch 120hp motor is nothing special or desirable and the 1991 and later 3.0 (181 cubic inch) motors are dirt cheap and 100000% better the boat isnt worth it. the boat probably weighted 1700# or...
  18. Scott Danforth

    Boat weight

    I would not even consider buying the boat unless you want a really expensive project. OMC has not been in business for decades, and the hull will need restoration before it can be used. that boat will cost you more than $8000+ and 2 years + of your time to get to a point to be safe and usable...
  19. Scott Danforth

    Adding hydronic cabin heat from a AQ140A engine

    You need to figure out how much extra volume you are adding. Determine what 8% of that is. Then determine if that extra 8% of expansion will cause an issue such as expelling too much coolant. If your motor utilizes a puke tank, you may need a bigger one.
  20. Scott Danforth

    Merc trim pump

    You could pull the switch apart and clean the contacts and reassemble
View older results
Top