Search results

  1. Scott Danforth

    stuck in neutral on 90hp due to shifter on console

    you need the shifter service manual for details like that. Suggest you start to pull it apart. usually a simple fix
  2. Scott Danforth

    Re-upholstery Job on Cruisers Yacht 338 Bowrider

    thats the part of the product that drives the OCD engineer in me absolutely nuts
  3. Scott Danforth

    1992 SFM190 Max Weight Aft?

    I can not compute this.......
  4. Scott Danforth

    1992 SFM190 Max Weight Aft?

    Welcome aboard I would be moving the batteries and coolers to the bow myself. keep in mind, Large adults are subjective. are we talking 185# people or 300# people. the capacity tag on the transom is the total weight of motor/gear/fuel/people/beer that the boat is rated for. what does that...
  5. Scott Danforth

    Bimini Measurements - Four Winn's SL262 - 2008

    if you dont have the bows/bimini, who's pic is that. if you need to buy a complete bimini setup. check with Great Lakes Boat Top since they most likely made the original.
  6. Scott Danforth

    Throttle control options for a 1991 Cobia with a 5.7 liter.

    the newer controls have same functionality all in the control depending on what control it is, there is a finger trigger along with the thumb switch, or a 2-stage switch
  7. Scott Danforth

    Boat engine hatch coring

    PL isnt going to cut it. it wont cut it on your transom if you mix a big batch of PB and make it a bit loose, about the consistency of yogurt, you can use that. but keep in mind, the bigger the batch, the less working time you have as it will kick faster. you will need to spread it with a...
  8. Scott Danforth

    prop for pontoon

    If you are overheating, you have a cooling system problem
  9. Scott Danforth

    Boat engine hatch coring

    Use corebond
  10. Scott Danforth

    Volvo Penta 2006 8.1 fuel injectors (OSI-BF 375 HP) Rinker 282 Captiva.

    Marine injectors are different than the automotive injectors I would contact Raylar and buy take-offs
  11. Scott Danforth

    89 5.0 fuel pump

    Thanks for closing the loop on this. yes, many times you need to clock the housing as you have done. Make sure to use blue loctite on the screws
  12. Scott Danforth

    Primer for Wood for oil-based Rustoleum?

    I would re-skin with 5052 myself. or I would get a sheet of starboard for $100 and use that.
  13. Scott Danforth

    Stable Fishing Boat for a Big Man

    the more pointy the front end, the less load it will carry up there. I recommend not stepping on the bow, however stepping into the mid section or the stern. a stratos or nitro or similar go-fast bass boat is intended to go from fishing hole to fishing hole at 70mph. Since it is just you...
  14. Scott Danforth

    Oil pan size

    you should also have an aluminum finned oil pan. I agree, leave it as is or go with a larger sump. FYI - even todays LT trucks with just a 5.3 in them have 8 quarts of oil.
  15. Scott Danforth

    Primer for Wood for oil-based Rustoleum?

    I would use the old timers wood preservative. https://forums.iboats.com/threads/options-for-water-sealing-wood.753380/post-5736460 or I would thin out the primer with some acetone and get a few coats on prior to the paint. if the skin is really pitted, i would re-skin it. did someone use...
  16. Scott Danforth

    89 5.0 fuel pump

    the motor is tired and while it runs, you only have about 80% of its original power. if the compression gets lower than 120psi, time for a rebuild
  17. Scott Danforth

    Searched - DIY Transom Cap Ideas

    local sheet metal shop, have them bend up a 5052 16 gauge or 14 gauge aluminum cap. soft enough to form with a rubber mallet. strong enough for your needs.
  18. Scott Danforth

    Searched - DIY Transom Cap Ideas

    reverse polarity, teflon liner, proper gas, yes. how do you have a mig without wire feed?
  19. Scott Danforth

    Chris Craft Restoration - Drooping fiberglass deck

    only thing you can do is try Me, I would use a hydraulic bottle jack and a heat gun, if after 30 minutes, no luck, resort to fairing.
  20. Scott Danforth

    Searched - DIY Transom Cap Ideas

    I have access to shop tools, I dont even think about this kind of stuff..... Just fire up the welder However you can buy transom cap material / trim material.
Top