Search results

  1. alldodge

    Tamd22 MD22 Earthing Thread.. Isolated Return. 55Amp Fuse.Help Needed

    I'm seeing additional grounds coming from the battery terminal. Some how one or more of them has a connection back to the block. Don't see the cables being the ground but it would only be possible if a ground wire is touching it
  2. alldodge

    B3 lower shift cable

    Hope this clears it up. You shouldn't need to readjust the 3 inch spacing, but if it was loosened then maybe. The good thing with a bravo, you can have the motor running and slide the barrel nut ot and make slight adjustments as needed. Just make sure the prop is clear and with someone...
  3. alldodge

    1995 Four Winns 7.4 l won't turn over ... Nothing

    You should have a 50 amp fuse between the assist solenoid and the starter
  4. alldodge

    Wiring question - starter

    I think your talking about the 90 amp fuse. The pic below shows the wiring, but does not show the orange wire for the alternator on the fuse which it should
  5. alldodge

    2004 350 mag winterization issue

    Just remove the brass insert and then you can get at the blue plug. In most cases they break because they get over tightened. The O-rings should be replaced every few times. What happens is the ring looses is elasticity and requires folks to tighten them more to stop a leak. If the ring was...
  6. alldodge

    Pressing Bearings Onto the Drive Gear

    You can use a 2 jar puller similar to this one. Pay no attention to the socket and breaker bar Now to put them back together, you need something with enough force to do it. A large bench vise, arbor press, or other. The issue is you need enough force with also enough room to be able to do...
  7. alldodge

    Blown Fuses

    As GM mentioned your running all your circuits from the battery using a 7.5 amp fuse. Using 14 gauge wire to feed the circuits means you should be able to use a 15 amp fuse. Maybe need to step back and look at again. You should have IMO at least 12 gauge (20 amp) feeding your bus bars, 10...
  8. alldodge

    Paint remover

    Have gotten tired of bottom paint so the plan is to remove it all, then either re-gel or more then likely paint with epoxy. A local place will blast it or I can use paint remover. There are several products which are caustic and others which are environmentally friendly. Leaning toward the...
  9. alldodge

    After Market Fuel Pumps

    Vapor lock is a different issue and is not caused by a weak pump, its caused by the fuel getting to hot. The booster pump can help but does not stop it in most cases. Ethanol gas also plays a part in the problem. The only way IMO to stop it completely is to reroute the fuel return which goes...
  10. alldodge

    trim button conversion

    Should be easy enough to change the wiring. The issue I'm running into is only able to find 1987 and up wiring. Now if your trim motor has only two wires on it this will work. http://www.maxrules.com/graphics/omc/wiring/TnTwiring.gif
  11. alldodge

    2016 Yamaha VF115hp lifting points?

    Don't know about your Yam, but I lifted mine by using to straps and tying them with another line at the bottom so then are held in place. Similar to this pic below but they are just using rope. Here one which can buy but should give you the idea of how Then this one was done by a member here
  12. alldodge

    4.3 not running like it should...where to start?

    Yes its 91-806901 but should also be able to get it from a local auto shop
  13. alldodge

    Winerizing 4.3l volvo penta

    If your sure it went up in there and next to no water came out, I would verify putting a bit of water in thru the water pump housing and see if it drains. If it does drain I would think your good. Some use a stiff piece of copper wire I'm not a VP guy but I to do not see the plug the folks...
  14. alldodge

    4.3L MerCruiser Alpha - Starboard Riser 100 degrees hotter than Port Riser

    One side will always be hotter then the other, its just the way water flows, its always to the path of least resistance. If you didn't have the spacer in there I would lean a bit more to inspection of the manifold but right now I lean more to the Thermostat housing. The exhaust you have is the...
  15. alldodge

    Winerizing 4.3l volvo penta

    The issue is your pics are to large. Need to set camera for less resolution, or use photbucket, or resize them. Removing the hoses off the exhaust will take care of them, if they don't have plugs on the hose elbows. The block drains do need to be removed, one on each side and they do need to...
  16. alldodge

    Winerizing 4.3l volvo penta

    I use the upload method in the pics below. The pics your seeing are uploaded from my PC
  17. alldodge

    4.3 not running like it should...where to start?

    The vacuum hose goes to the PCV valve on the valve cover. With the hose disconnected it gives the motor a large vacuum leak. ​ The timing light you have needs to have an inductive pickup. The pickup will have a clip of sorts which goes over the number 1 spark plug wire. Connect the other...
  18. alldodge

    Converting 4.3l Mercruiser to inboard

    The belt routing and part numbers should be the same as the 5.7 for the inboards. Could look up a 97, 98 and should be the same http://www.mercruiserparts.com/350-mag-mpi-mie-gen-gm-350-v-8-1998-1
  19. alldodge

    92 Camry dead battery

    Bought a Camry for the grandson's first car. Installed new battery and checked the charging circuit and all doing good. Parked it and it sat for more then a week. Tried to start it and nothing, dash lights wouldn't even come ON. Battery was dead, so recharged and go it running. The ALT...
  20. alldodge

    Cruiser restoration and wheelchair adaption

    Had to do some searching on Airtonic to find your unit, there are several companies from assault weapons to radio controls. That is a nice little heater and doesn't use much fuel. Looks like only item left to install is the air intake The wood is coming out nice, she is going to look great...
Top