Search results

  1. Scott Danforth

    Used Maxum

    its a 21 year old boat (which means consider it a project). so condition means everything other than that, Maxum no longer exists as a brand. it was a low-level brunswick brand (bayliner/searay/maxum)
  2. Scott Danforth

    ANOTHER WATER IN OIL QUESTION

    run your water jacket pressure test at 15 psi. should hold indefinately the water in the manifold may be a secondary issue. how did you winterize? Eastern NC got well below freezing this past winter a few days.
  3. Scott Danforth

    Water inside boat

    first, welcome aboard second, remember, boats are designed to last about 15 years and be replaced as they start to fail a few items that can cause the water leaking as you describe: leaking rub rail that only leaks when you cut to port due to water splashing up the sides of the boat crack in...
  4. Scott Danforth

    Brand New, about to be, Boat Owner need advice about purchase

    good luck.... if it smells like a scam, looks like a scam, and you cant actually put your hands on the boat to inspect it first hand, it is a scam.
  5. Scott Danforth

    Wayyyy over propped???

    goes to show how much BS is on the internet. your cranking PSI is ball-park your compression ratio times 1 atmosphere. so a 9.5:1 compression ratio will be about 140 psi. it was true in 1862 and when Nicolaus Otto built the first 4-stroke in 1861, it is still true today. from the Yamaha 250...
  6. Scott Danforth

    Cobalt 232 swim platform repair

    you made more work for yourself now that you cut the skin vs separating the skin at the seam. like AD stated, the force prior was only a few PSI over the whole surface, now its about 15 times that, concentrated over the seam you cut. you will need to bevel back the remaining skin about 3"...
  7. Scott Danforth

    Wayyyy over propped???

    no way your compression is 200. you would need a diesel engine to have compression that high. check your gauge
  8. Scott Danforth

    Any way to remove Hotjar "Feedback" box from screen?

    so can the mods turn if off?
  9. Scott Danforth

    18' with bravo 2 drive on a single 4.3

    Welcome aboard Bravo 2 drives are for pushing houseboats and tug boats. someone would have had to swap that drive onto an 18' pleasure boat. especially one with a V6 the Bravo 2 drives are usually set up with huge props and V8's or diesels I would pass on the boat. what else was slapped...
  10. Scott Danforth

    Cut holes in doghouse?

    is it really slowing down, or just getting quieter? as stated, closing the doghouse would not effect the idle of a boat, especially as quickly as you describe unless you are moving wires with questionable connections. even if the box was 100% air tight (as in compression gaskets, etc), it...
  11. Scott Danforth

    Help! 1976 Mark Twain restore it or junk it?!?

    and there is the rub. you will spend about $8-$10k on properly restoring the hull and interior (this years pricing, up about 100% from 2019 pricing) and that is assuming your motor is perfect. your boat in perfect shape is a $2000 boat restoring boats only makes sense if you love the boat or...
  12. Scott Danforth

    Boat doesn’t idles smooth. Is my Timing off?

    make sure every passage in the carb is clear with a fine wire or piece of fishing line service your points, set dwell (with a meter) and then set timing then adjust your idle speed both these things effect your idle
  13. Scott Danforth

    Atwood surge coupler welded on Prestige trailer

    I would fire up the die grinder with a cut-off wheel and weld a different actuator
  14. Scott Danforth

    Electric fuel pump

    the octane of the fuel and the lead requirement are two completely different issues. octane is needed to combat detonation (pre-ignition). lead is used as a lubricant for the valves (that may have had a very minor effect on combating detonation) you need the lead or lead substitute because...
  15. Scott Danforth

    Where to mount my transducer?

    first, put the tape measure on your transom, and not 4 feet away second, mark the CL of your transom, put a line 15" from the CL. then turn your motor full right turn and see if you have clearance. if so, then mount the transducer.
  16. Scott Danforth

    Can i get 4 blade for my boat? 1979 Evinrude 35hp 2 Stroke

    not sure you have enough motor to run a 4-blade
  17. Scott Danforth

    Wayyyy over propped???

    im thinking you need to verify your tach and that the motor is running right.
  18. Scott Danforth

    Jumpy Tach

    my guess bad connection somewhere or the tach is going south
  19. Scott Danforth

    Help! 95 5.0 efi ford firing order

    by looking up your serial number and getting the proper manual for it.
  20. Scott Danforth

    Cut holes in doghouse?

    no
Top