Search results

  1. Scott Danforth

    Buying a used boat anxiety-talk me down.

    Yes, boats are designed with a 15 year design life. they are designed to be bought, used, and replaced so that they can still make boats. SeaRay re-designed their hulls in 2002 when they moved the small boats to Mexico. while it may not have wood, the plexus joints crack over time. $20k is...
  2. Scott Danforth

    485 Merc starting hard, running rough and wont idle

    its never the coil. coils either work or down. what is your compression numbers? what is your fuel pressure? what is your starting procedure? when was the last time you cleaned the carb?
  3. Scott Danforth

    Head gasket? Cracked head?

    before you pull anything apart. pressure test the cooling system, do a compression test as well as a leak down test. without the diagnosing of those 3 tests, you are looking for a needle in a stack of needles.
  4. Scott Danforth

    Rotted transom good stringers.

    that looks like original glass covering the transom and stringers
  5. Scott Danforth

    Crusader 454 Cooling

    2000 hours means there is 1500-2000 hours of life left. At 350hp, BBCs should last about 6-7000 hours as that is not stressed. Barnacle buster is just muriatic acid and water. Agreed, not that good on shafts or the seal springs. Oxalic acid would be milder Is the HX factory OEM, or...
  6. Scott Danforth

    Repowering 97 crownline. Best options?

    Exactly, and most "marine mechanics" are not factory trained or qualified
  7. Scott Danforth

    Another v6 to v8 swap question

    You dont just add material, you want the motor attached to something solid. If the mount fails, usually the motor moves enough to cause issues......like sinking
  8. Scott Danforth

    Another v6 to v8 swap question

    you mean the motor mounting blocks? then yes, cut out the old, hang and align the motor and then build new motor mounting blocks and glass them in to come up to the new motor mount location.
  9. Scott Danforth

    Tying to dock/reaching it

    boat hook is your friend
  10. Scott Danforth

    Need help wiring up electronic ignitor

    and what kind of motor is the distributor installed on, and why are you not following the pertronix instructions?
  11. Scott Danforth

    1984 470 initial carb set up to get idle

    if you have a new cam, that is 20 minutes at 2000 RPM to break in the cam and lifters prior to the normal break in proceedure which is varying loads.
  12. Scott Danforth

    Repowering 97 crownline. Best options?

    buy a running motor for $300 and swap it in ~ $1000 out of pocket (price of motor, gaskets, incidentals) buy a complete long block for $3800 and swap it in ~ $4400 out of pocket (price of motor, gaskets, incidentals) buy a complete stroker long block for $6000 and swap it in ~ $6600 out of...
  13. Scott Danforth

    Material Availability for DIY/Home Improvement Projects?

    a pressure treated 2x4 is currently $15. used to be $4
  14. Scott Danforth

    1984 470 initial carb set up to get idle

    most likely corrosion somewhere along the circuit
  15. Scott Danforth

    Repowering 97 crownline. Best options?

    Joe, welcome aboard being a 1997 is not that old. generally the motors in boats are usually murdered, only very few wear out (4000+ hours) is your boat carbureted or fuel injected? Alpha or Bravo drive are you looking for stock reman or more power? you will need to determine the cause of...
  16. Scott Danforth

    Mating Engine to Mercrusier problem

    Any 1986 and later GM SBC manual transmission 153 tooth flywheel ( for 10" clutch) the should be about $70 for cast iron and $150ish for SFI rated billet steel
  17. Scott Danforth

    Scout 153 leaking aerator problem

    measure what you have. you either have 3/4" or 1-1/8" and no, fix any other issue.
  18. Scott Danforth

    Drain tubes

    drain tubes are expanded in place you need a drain tube or water will rot your transom like 'kogs indicated
  19. Scott Danforth

    Mating Engine to Mercrusier problem

    NO, the drives are very similar. however the engine on the other hand went thru 3 major design changes and a bunch of minor changes your boat being a 1981 may have a 1980 block first design change was block changed in 1980 for the 1981 model year. this flopped the dip stick and there were...
  20. Scott Danforth

    1984 470 initial carb set up to get idle

    so this thread was started after your thread on a motor missing on 1 cylinder?
Top