Search results

  1. catfishcarl99

    is this video correct need ignition help

    bumping this up thanks.
  2. catfishcarl99

    is this video correct need ignition help

    now starboard side 4 wire plug to the base (trigger). tan and green. infinate open. next is tan and greenish. 35 ohms. normal. the last is the green and greenish. infinate open. so whats bad lol. according to the video its the stator. but im thinking trigger since the wires that show open are...
  3. catfishcarl99

    is this video correct need ignition help

    now testing the big plug he said it stator but run to firing base (trigger) port and starboard have a tan with stripe, green, greenish, and a black with stripe. first pic is port tan and green. 33 ohms. next is port tan and greenish 34 ohms. then green and greenish on port. 65 ohms. all in the...
  4. catfishcarl99

    is this video correct need ignition help

    this is my readings from the 2 wire plugs he calls the trigger test. i can see they run to the stator. thats why im confused
  5. catfishcarl99

    is this video correct need ignition help

    i have a 1980 115 v4. evin, i have no spark on the lower straboard side. i did these exact tests in this video. i have 550 ohms on port 545 on starboard on the 2 wire plugs he says is the trigger. the leads go to stator. CONFUSED! i had around 35 ohms on port and 65. like he did on the plug with...
  6. catfishcarl99

    force/chrysler engine swap wire harness

    ok guys im popping on to get some advise on this. I have a 76 stripped and rebuilt 75 hp chrysler motor 757HB. its going on to replace a 1989 507Y9B underpowered 50. wiring harness on the boat to the 50 that's leaving is as follows. pics attached. top to bottom start yellow/red tach gray/black...
  7. catfishcarl99

    force/chrysler wireing harness swap

    ok guys im popping on to get some advise on this. I have a 76 stripped and rebuilt 75 hp chrysler motor 757HB. its going on to replace a 1989 507Y9B underpowered 50. wiring harness on the boat to the 50 that's leaving is as follows. pics attached. top to bottom start yellow/red tach gray/black...
  8. catfishcarl99

    quick head gasket question

    I just rebuilt a 76 Chrysler 75 hp. got a new head gasket with the sealer in it. so if the heat seals it up should I run it for a min or two on idle to get it sealed up before putting lower unit on or just hit with water on start up?
  9. catfishcarl99

    possible block cracked?

    so I went to start and successfully did start my motor I have been working on. I put a hose on the water inlet since I don't have an impeller yet. it came through the pee tube I added to the top of head but when I started the motor for 30-40 seconds the water was running back down through the...
  10. catfishcarl99

    wiring harness ignition for testing

    so recently I purchased two Chrysler 75 hp engines for I would say a steal. $150 for two complete engines. one was in rough shape and seized. other turned freely but had 125 152 40 on compression. I just completely went through the engine and re ringed it. its all back together and passed...
  11. catfishcarl99

    chrysler piston ring gap specs?

    can someone with a manual or that knows the gap for rings on a 1976 75 hp Chrysler model 757hb pass it to me. restoring one now. got 2 exact models for $150. ran a hone through them I want to properly gap new rings before replacing pistons.
  12. catfishcarl99

    looking at a chrysler 75 hp to restore possibly 2 thoughts?

    i found a couple 75 hp Chrysler motors for sale. listed at $100 each or make offer. calling tomorrow about them. not sure if they are complete (carbs ) ect… I have a 1989 force 50 hp on a 17' spectrum fish and ski. the motor runs really well but 25mph with me and 5mph with my girlfriend and 2...
  13. catfishcarl99

    carb part replacement float

    I have a force 50 hp 1989 us marine model 507y9b. I want to gather up some parts to rebuild the carb this winter. I want to replace the float old tin one brass whatever with a new plastic float. I know there has to be some out there as I see the rebuilt whole carbs on ebay with them in it but I...
  14. catfishcarl99

    cylinder not working force 50 507y9b

    so last season I had an intermittent issue with 1/2 power. this spring it worked fine then the issue returned. I had it running at home and pulled the lower plug wire off. no change. figuring it was a bad coil as I had changed thee top one out a few years ago I got another coil. worked great for...
  15. catfishcarl99

    Catfishing Season 2013 open discussion and photos

    Re: Catfishing Season 2013 open discussion and photos here in il im about ready to hit it. i fish a 5000 acre cooling lake. a long narrow flooded creek channel thats chalked full of chasnnel cats and flatheads. no blues unfortunatly. but last season i boated 173 cats. not per my boat. that was...
  16. catfishcarl99

    first bass mounting

    Re: first bass mounting just finished my 10 lb 8 oz drum. caught this summer. mounted for practice.
  17. catfishcarl99

    first bass mounting

    Re: first bass mounting i did a skin mount because the customer brought me a frozen fish. and skin mounts are cheaper. and bass reproduce. the customer wants a big ol mouth. and this one isnt distended as alot ive seen. the fluid line should run from tail to lower mandables and this one does...
  18. catfishcarl99

    first bass mounting

    Re: first bass mounting 14 colors in all + sealer and gloss. and i tipped the scales with gold oil paint before glossing and adding the shimmering colors. now for a piece of driftwood. im pretty satisfied with this being my first fish. got a 10lb 8 oz drum im mounting tomorrow just to hang...
  19. catfishcarl99

    first bass mounting

    Re: first bass mounting looks good. this one was 21. pretty close. i just got done with mine.
  20. catfishcarl99

    first bass mounting

    Re: first bass mounting paints, gloss and scale tipping paint arrived today. got the eyes set with epoxy. be painting this evening.
Top