Search results

  1. H

    6.2L MX MPI Stalls when shifting out of gear

    I think the work around you described is actually what was done on my engine, and outlined in the screenshot prior?
  2. H

    6.2L MX MPI Stalls when shifting out of gear

    I will also verify this too — thanks!
  3. H

    6.2L MX MPI Stalls when shifting out of gear

    I will test and report back
  4. H

    6.2L MX MPI Stalls when shifting out of gear

    Thank you. Do you happen to have the ability to screenshot the diagram of how it should be routed so I can verify?
  5. H

    6.2L MX MPI Stalls when shifting out of gear

    I will check and report back. Just to confirm I am understanding this test here, I am to remove the lower shift cable arm from the bracket, then pull/push it with two fingers, and it should move like butter, correct?
  6. H

    6.2L MX MPI Stalls when shifting out of gear

    Roger that about the Bravo ECU. Could you clarify your latter point about the dragging. Are you saying the lower shift cable is likely dragging/has resistance, and likely holding the switch down for longer than necessary?
  7. H

    6.2L MX MPI Stalls when shifting out of gear

    I believe it’s using an Alpha ECU, but will have to double check. I believe it is wired to ground the coil per this screenshot’s instructions.
  8. H

    6.2L MX MPI Stalls when shifting out of gear

    Same mechanic that installed the transom plate, gimble and engine. The cable is SEI. Where should I be checking for binding?
  9. H

    6.2L MX MPI Stalls when shifting out of gear

    Will do. I can do that in the water, correct? If there is, what is the solution? I would be surprised because the lower cable is brand new.
  10. H

    6.2L MX MPI Stalls when shifting out of gear

    I will check to make sure the distance from Barrel to Eye is 6 inches.
  11. H

    6.2L MX MPI Stalls when shifting out of gear

    An upper or lower cable? Or both?
  12. H

    6.2L MX MPI Stalls when shifting out of gear

    Maybe I should try loosening the screws and moving the switch a bit back from the activating lever?
  13. H

    6.2L MX MPI Stalls when shifting out of gear

    Pulled this from another thread. Are you referring to the bolts circled?
  14. H

    6.2L MX MPI Stalls when shifting out of gear

    Not shifting slow See the image below (found it online) of what my switch mount looks like. Are you referring to the two screws holding it in?
  15. H

    6.2L MX MPI Stalls when shifting out of gear

    How do you adjust the switch? I only see two screws holding it in place. Its the plunger type switch, not the roller one
  16. H

    6.2L MX MPI Stalls when shifting out of gear

    Alpha One Gen 2
  17. H

    6.2L MX MPI Stalls when shifting out of gear

    At the beginning of the season, I had my boat re-powered with a used 6.2L MX MPI engine. Part of this was also a new transom plate, gimbal, lower unit shift cable and bellows. However, a problem I have been running into is that the engine stalls about 75% of the time when shifting from gear into...
  18. H

    Problems starting after fuel filter/water separator change

    One thing that I did notice last time I was down at the boat is that while cranking, the Tach goes crazy. Not sure if that is relevant
  19. H

    Problems starting after fuel filter/water separator change

    I just purchased a basic code reader, its coming tomorrow. I will circle back with any codes it throws.
  20. H

    Problems starting after fuel filter/water separator change

    Confirmed spark today with a spark tester.
Top