Search results

  1. brianvolt7

    Neutral interlock switch Force 120 adjustment

    Hey all, I am looking for the procedure to adjust the neutral interlock switch on my 1990 Force 120. Any help would be great!
  2. brianvolt7

    Stalling Force 120 when popped into gear

    I have a 1990 force 120 with an 89 125 top end (long story). Runs great on plane, fires right up, however it dies when engaging into forward or reverse unless I rev it a bit. It seems to idle ok once I bring it back down. It happens when I start it after its warm or on initial start up. Any Ideas?
  3. brianvolt7

    Good Boat names

    Re: Good Boat names Try this one on for size!
  4. brianvolt7

    Pre-mix gas or not to pre-mix gas

    1990 Force 120 I have always pre-mixed my fuel 5 gallons at a time and then filled the boat. It takes about 20 gallons. Recently, and for the first time, I poured the oil into the tank then filled the boat at the pump. I experienced some dramatic performance deficiencies with the motor. Does...
  5. brianvolt7

    Force 120 exhaust leak question

    1990 Force 120 on Bayliner 20 ft. cuddy. I have recently installed a new powerhead on the motor leg. I confirmed that when I changed the powerhead I did not reinstall the exhaust gasket on the leg. It is the gasket that goes on the very bottom of the exhaust leg where it enters the lower unit...
  6. brianvolt7

    Stripers- Any experts

    I am planning Striped Bass fishing trip to the Sacramento river, between Sacramento and the East side of Suisun bay. I am fishing for Striped Bass and this is the first time. I have never fished for Stripers before. The fish are between seasons now but I want to be ready for the fall run with...
  7. brianvolt7

    Bayliner w/Force that hangs low towing

    1990 Bayliner Capri cuddy with a 120 horse Force Motor I have owned the boat now for three years. I do have a trailer bracket for the motor but the motor only has about 10? of clearance to the pavement when towing. It's fine for highway but I usually need to tilt it up when I get to my...
  8. brianvolt7

    Any one know- Force motor A, B or C-- rings & pistons?

    1990 force 120 Does anybody know how to identify what motor I have. Model A, B or C. There is a sticker on the top left of the block that reads: 1201X90A There is a stamp on the block in the lower left that reads: MG38488 The pistons are stamped with a 2 Model A is a different size rings than...
  9. brianvolt7

    Pistons, Rings, JB weld ?????

    Re: Pistons, Rings, JB weld ????? Here is my number 4 and head gasket. Though I mentioned I want to go the least expensive way, I still want to do it right.
  10. brianvolt7

    Pistons, Rings, JB weld ?????

    1990 Force 120 on Bayliner cuddy Can anybody tell me why the number two and four pistons are pitted? I was told that I could use any piston ring as long as it is the same size, is this true or do I have to buy Force piston rings. Can I use standard rings or do I have to have a shop bore these...
  11. brianvolt7

    Secret trout bait

    Re: Secret trout bait I use to fish brookies in the Ermabells in Oregon. Used a full night crawler puffed up with air. They ranged 15" to 18", limit two. about a mile or so hike in. Also would go to hidden lake by Cougar reservoir, hike up the stream in the snow to the lake. 10"-12" natural...
  12. brianvolt7

    Throw the money in that hole in the water

    Re: Throw the money in that hole in the water My other hobby:D This hole is a 15 minute quad ride from my house. On private roads we are 10 minutes to forest land.
  13. brianvolt7

    Need Help With Force Motor

    Re: Need Help With Force Motor More pics of number 4 and head gasket. Should I fix the rings put a new head gasket on it and sell it? Or is it worth replacing the piston on number 4 and keep it.
  14. brianvolt7

    Need Help With Force Motor

    Re: Need Help With Force Motor Here are my pics. There is not any scratches on any piston walls that my fingernail catches on, in fact the scoring on the walls is light even on the trashed pistons. My main concern is the chip, and I have no Idea what is up with #4:confused:
  15. brianvolt7

    Head gasket or rings? Compression testing

    I read in a post a while back that there is a spray that can be put into the dead pistons that seals the rings to tell if the problem is rings or head gasket. Does this sound familiar to someone? Can anybody share this proceedure with me?
  16. brianvolt7

    Throw the money in that hole in the water

    I am not one to keep track of the cost of hobbies, but my wife mentioned that it seems like my boat is the most expensive hobby I have. I decided to account for the project. Here is what I have spent on my boat over the last three years:( Boat: 1500 Floor: 325 Upholstery: 70 Timing light: 30...
  17. brianvolt7

    How to post a thumbnail or full size pic

    I am sure that this has been covered but after searching the forums I didn't locate any specifics on the topic. How do you post a full screen pic or thumbnail pics. For some reason my pics are allways to large to attach to the thread so I end up converting formats, shrinking etc. If someone...
  18. brianvolt7

    Secret trout bait

    Re: Secret trout bait Someone has mentioned something almost like it, shrimp sandwich. SALAD SHRIMP FLOATED WITH POWER BAIT OR MARSHMELLOWS Now you may not believe that it works as well as I say it does, but where I fish, it is a killer. I out fish everyone 5 to 1. Here is the rig, make sure...
  19. brianvolt7

    Secret trout bait

    Just had to tell everyone that today at the lake that was recently stalked my family knocked the planters dead. People lined the bank, we caught our limit in about 1 hour while everyone else around us didn?t even get a bite (boat wont start, I am working on it) literally not a bite! Smallest 11"...
  20. brianvolt7

    Can anybody tell me what this is?

    Can any body tell me what this electrical componant is? Motor-1990 Force 120 L drive. Is this the voltage regulator?
Top