Search results

  1. I

    Can't find Fuel filter for 2003 bayliner 5.0

    hi guys i looked on google and can't find the cross reference numbers for fuel filter 70573 . That is my fuel filter right? It a 2003 bayliner 205 5.0.. thanks in advance
  2. I

    Skeg broken ? Alpha one and bravo same ?

    hi I have a broken skeg ( bottom half ) on a alpha one gen 1 . I found a skeg for a Bravo 1 . Are they they same size ?
  3. I

    Does the Fuel line have a washer/gasket?? Leaking !!

    Hi guys i have. Mercruiser 3.0 engine on a 2003 bayliner I'm getting leaking fuel from the fuel line that connects to the Carb.. the brass bolt area . Is it supposed to have gasket ?? It's just metal flare tube against a concave metal ? I don't remember seeing a gasket ?
  4. I

    Rebuilt carb now confused lol need help

    hi guys ok I took out my 2 barrel carb off my merceuiser 2003 3.0l and rebuilt it.. pretty easy but I have couple questions and issues The replacement accelerator pump is a little shorter than the original ? And also want help with adjusting the links and rods.. the manual makes no sense .. i...
  5. I

    Confused !! 2003 bayliner mercury 3.0l 181 plugs??

    Hi guys I have a 2003 bayliner with the 3.0l 181 cid engine.. what plugs are for it? And what's the timing for it? My flame arrester says 1 degree ATDC ? But I put in my serial number listed on it on google nothing comes up? Also what type of carb does that engine have ?
  6. I

    Light white smoke / steam water ?? Normal ?

    Hi guys , I have a 2003 bayliner 3.0 mercury and after 3-4 months of sitting I went to start and run it to clean the carbs with carb cleaner ( I heard doesn't do any good ) but did it anyways .. I've always had hard time running her without hiccups and bogging down .. at low Rpms under 1500...
  7. I

    Tilt trim just clicks 2004 bayliner 175

    Hi guys, ok i had an issue with the trim motor last year cleaned the terminals and worked fine.. Months later didnt work but after 20 presses ir worked.. Worked for months.. Now about to sell it and it wont work.. It just clicks from the rear.. Made sure all connections are getting 12-13v. But...
  8. I

    Bayliner multiple gauges not working ??

    Hi guys i have a.2003 bayliner with the 3.0 mercury engine and the Rpm gauge dont work, the MPh kinda works goes slowly up to about 25 mph even though im going top speed.. Also volt meter probably bad to always shows 10v ?
  9. I

    Bayliner pulls left?

    Hi guys, my 2003 175 bayliner with the 3.0 mercruiser engine and alpha gen 2 drive pulls left on its own.. itll do circles all day lol
  10. I

    Wont shift into fwd when it does it slams hard?

    Hey guys , ok long story short.. i told my uncle not to touch the boat because he dont know how to operate it.. well i came back and it wont shift onti first , after many attempts it will catch... but sometimes it revs high and catches and that impact is nasty.. i hope he didnt mess anything...
  11. I

    mercury mercruiser 3.0 shift cable issue engine dies out?

    hi guys ok heres the rundown.. i replaced the shift cable because i was replacing a ripped shift bellow and after all that was done,, now its hard for me to adjust the lower shift cable, i heard its 6 inches from center stud to outer hole but at 6 inches that big golden nut that swivels.. i...
  12. I

    Bayliner leaking :(

    Hi guys my 03 bayliner 175 3.0 mercury is leaking i believe its the shift cable boot its all ripped up, can i replace just the boot without taking the whole drive off ? 2nd issue is it wont start , sometimes it does for a split second or 2 and cuts off a couple times it did for 10 seconds and...
  13. I

    2003 Bayliner 3.0 Mercury mercruiser grease fittings?

    Hey guys i see a bunch of fittings on the outside drive housing whatever u call it lol.. i bought a grease gun and grease.. how do i proceed on greasing this baby? also when i disconnected the steering cable and i can move the drive freely but it makes a rubber squeege friction noise to the left...
  14. I

    Stiff steering ?

    Hello , i have a 2003 bayliner 175 with the 3.0 mercury inboard . My issue is the steering is very syiff, i just want to go ahead and change the whole thing it looks pretty simple but i want to know is ot ok to grease up the rod in the back? Or is that a no no? Maybe thats whats making it hard...
  15. I

    First boat.. : / few issues and i need some advice

    Hi guys, ok i just purchased a 2003 bayliner 175 3.0 mercruiser and i took it out to tye water it took a while to crank her but she did and she ran .. but steering was so hard.. im probably going to just replace the teleflex cable , that sounds right? Also i noticed rust all over the engine ...
View older results
Top