Search results

  1. alldodge

    Started out as a good day on the water. 4.3 mercruiser

    Need a scanner, and do to no spark Start with distributor car and rotor (I know just replaced last year). Make sure 12V stays on the coil full time when ON and when cranking. Next it gets into things like crank position sensor
  2. alldodge

    What is the correct name for this breaker?

    The pic in post 2 is a marine rated breaker and is used by VP, Merc and others. Can find them in a lot of places
  3. alldodge

    What is the correct name for this breaker?

    Yes, with caveat, there will be no issue so long as nothing shorts out. My guess is nothing will. You will know if there is a problem by a big a$$ spark when wires connect together, little spark is ok ;)
  4. alldodge

    What is the correct name for this breaker?

    Yes, but keep in mind jumping it with bad connections may not change anything if jumper does not make a good connection
  5. alldodge

    What is the correct name for this breaker?

    Remove the breaker from wires and clean everything up and reinstall When you have breaker off and clean, put meter on ohms scale and touch one probe on each terminal. You should read 0,0 ohms Note, don't do this test with any wires connected to it
  6. alldodge

    What is the correct name for this breaker?

    no, red probe on one of the terminals and black probe on ground of Bat of the block Put red probe one at a time on each terminal of the breaker, they should both read the same
  7. alldodge

    What is the correct name for this breaker?

    yes, 0-20 you should see full Bat voltage 12.6 to 12.7 Black probe on Bat ground
  8. alldodge

    Box anchors.

    If the bottom is soft (mud, clay, sand) than a box will hold. If winds change they will dig in at another direction, all good Cons Not good with weeds, rock as they get tangled or have nothing to dig into. Can get hung up with stumps Must get directly over the anchor to pull up. They do not use...
  9. alldodge

    What is the correct name for this breaker?

    Yes
  10. alldodge

    Carb problems on 1994 Mercruiser 7.4 Thunderbolt V

    Yes, to both I'm working off what you say, it leaked during priming? Not leaking when running is the way it should be, but also should not leak when priming. Note: the priming bulb will be removed when done, right?
  11. alldodge

    What is the correct name for this breaker?

    I would use a meter to see if power is not passing before replacing It's most likely just a standard push button breaker under the cover https://inverterservicecenter.com/40-amp-medium-duty-push-button-circuit-breaker-blue-sea-2141
  12. alldodge

    Carb problems on 1994 Mercruiser 7.4 Thunderbolt V

    Assuming the primer bulb is just for testing The float level is set to high or the needle valve is not closing off the fuel when full
  13. alldodge

    1989 doral300 steering leak

    Welcome back Your issue has nothing to do with the type of boat and has everything to do with who makes the steering, Merc, VP, other???
  14. alldodge

    bravo 3 leaking input shaft help

    Manual 28 page 3A-57 and 3A-58 shows how to set clutch gears timing This is done prior to installing the drive shaft. The question is, does this need to be done again if only the drive shaft was removed? I would say yes because the clutch gears could move with the drive shaft going in/out...
  15. alldodge

    Refresh to Dash Project

    nice work
  16. alldodge

    dual outdrives

    Normally the blocks would not be on your drive but if they are there they would be on the rod item 13
  17. alldodge

    3.0L mercruiser compression

    It's fine unless you threw some water and crud in the tank
  18. alldodge

    3.0L mercruiser compression

    Doesn't everyone throw water and crud in the tank to get more out next season ;)
  19. alldodge

    Trim went full up on it’s own

    Might be the plug connection next to the pump, Look for a black rubber plug with 3 wires
  20. alldodge

    Trim went full up on it’s own

    Those switches go bad This is up to you, can put new switches anywhere, but I would get into handle and fix.
Top