Search results

  1. Scott Danforth

    which carb to upgrade/replace too

    its the barbed fitting on the tank
  2. Scott Danforth

    Grease Seal to Spindle Fit

    the issue with the lisle bearing packer is you have to clean it between each use which takes about 2 mintues....... where a dab of grease in the palm of the hand takes 30 seconds to pack the bearing and wipe your hands.
  3. Scott Danforth

    Random

    hell, I used to slap the dash to get the heater motor to come on or get the tape to eject from the head unit.
  4. Scott Danforth

    Identify the thread of this screw from my boat

    0.1875 is usually condensed down to 0.188 or 0.19.
  5. Scott Danforth

    which carb to upgrade/replace too

    buy a lottery ticket.
  6. Scott Danforth

    which carb to upgrade/replace too

    see post #13
  7. Scott Danforth

    which carb to upgrade/replace too

    FYI, you should not need to pull the carb or strip it, only remove the bowl and metering plate to clear the accelerator pump circuit. this will help you. https://www.carburetor-parts.com/assets/manuals/holley-2300-4160-manual.pdf clean out this passage. you will need to carefully remove...
  8. Scott Danforth

    Been a little cold.

    dont complain when we send you 95 degrees and 98% humidity.
  9. Scott Danforth

    which carb to upgrade/replace too

    I apprenticed under my grandfathers Heating and Plumbing business from the time I was 12 to about 18. he was looking for help, I managed to get a lot of experience. I can re-plumb a house and service the HVAC.... Dad got me into turning wrenches on cars at the early age of 3. learned how to...
  10. Scott Danforth

    which carb to upgrade/replace too

    that did not mechanically clean the passage you are lucky you did not blow up. cardboard is not fuel proof only if the parts changer at the dealer boogered up the jets. not much to them. its a brass screw with a hole in it.
  11. Scott Danforth

    which carb to upgrade/replace too

    I will add, if you choose to rebuild the carb yourself, we will walk you thru it. but there are many capable carburetor shops in the UK
  12. Scott Danforth

    Identify the thread of this screw from my boat

    The Bibles of bolted joints
  13. Scott Danforth

    Identify the thread of this screw from my boat

    because a 3/16" machine screw is a #10
  14. Scott Danforth

    Frozen engine manifold cracks and likelihood of block survival

    since the dealer was too dumb to winterize, I would run away even if they offered a new motor because I would not trust them to swap it correctly, however that is your call the block and heads did NOT survive. being a post 2014 mercruiser designed block, that motor is only available from...
  15. Scott Danforth

    which carb to upgrade/replace too

    here is a side view of the carb. the newer ones have hex screws, the earlier ones have slotted scrws. the whole kit is holley part number 703-036, however you only need the two blue gaskets. you can buy a two pack from Summit and with shipping, etc. have it to you in the UK by Friday...
  16. Scott Danforth

    which carb to upgrade/replace too

    the part changer at the dealer (can not call them a mechanic) did not clean out the accelerator pump passage. on a holley, that is on the bottom of the fuel bowl and first to plug. you are describing a failed accelerator pump circuit. again, your carb is fine, just needs $10 worth of cleaner...
  17. Scott Danforth

    4.3 crankshaft/housing oil leak - next steps?

    mercruiser buys the GM part and multiplies their cost by 5x. the ECM, wiring and exhaust are the only things on that motor that Mercruiser supplied. everything else came from GM here is Achris's write up of the same issue and how it was resolved...
  18. Scott Danforth

    Identify the thread of this screw from my boat

    No, read the book 50 years ago, also own the two bibles of bolted joints
  19. Scott Danforth

    Identify the thread of this screw from my boat

    Phillips screws were designed by Henry Ford to limit the torque that the line workers could apply. The bit would cam out prior to stripping
  20. Scott Danforth

    which carb to upgrade/replace too

    What is your compression? What is the fuel pressure? What is the timing set to? Dying on WOT is most likely fuel delivery, not the carb Doubt the carb need replacement. Been wrenching on Holley carbs for over 50 years Summit racing can get you jets in 3 days from the states. Can even get...
Top