Search results

  1. alldodge

    2012 Mercury 9.9hp 209cc won't start

    Lots of fuel out the plug holes, would say your flooding. Need to get back into the carb and check float level and if there is a piece of crud in the needle seat
  2. alldodge

    Gen 2 speedometer connector

    Item 34 https://www.mercruiserparts.com/bam/subassembly/30862/2686/100
  3. alldodge

    5.0GL-C won’t get on plane

    If pump wasn't pumping because of some crud inside which is now clear, some of that may have made its way into the carb
  4. alldodge

    Random cutting out 4.3 mercruiser

    The temp is on the front of the intake and has 2 wires The diode is most likely the Red plug. The more I think about it, its not the diode
  5. alldodge

    Random cutting out 4.3 mercruiser

    Being TKS might have an issue with the Temp switch, diode or TKS module. Anyone of the above if it starts drawing more current, may drain power from the coil
  6. alldodge

    Random cutting out 4.3 mercruiser

    BTW which 4.3 do you have, SN is best, but at least year and type?
  7. alldodge

    Random cutting out 4.3 mercruiser

    Have you pulled the 10 pin plug?
  8. alldodge

    Random cutting out 4.3 mercruiser

    key switch maybe
  9. alldodge

    towing capacity question

    My boat weights about 1K less dry then yours and I use a 3/4 with class 5 hitch. No issues
  10. alldodge

    5.0GL-C won’t get on plane

    Maybe use jumpers and hot wire the pump directly. If it runs and fills the filter/carb then would be another issue
  11. alldodge

    5.0GL-C won’t get on plane

    Does the pump run when motor is cranking? If not, is fuse blown?
  12. alldodge

    Quicksilver 3000 throttle control button install

    Each can be different, I wouldn't know without looking at it my self. Look at the opening and see if there is something that may show which way
  13. alldodge

    Quicksilver 3000 throttle control button install

    Move forward without touching the throttle only button. It should be able to be removed
  14. alldodge

    Automatic trim tabs

    Auto tabs are great when they work, but I've replaced 6 units so far. I would just get tabs and forget about the auto
  15. alldodge

    TWIN 1994 VOLVO PENTA 8.2 OVERHEATING

    More info??? Brand new installs and is boat in the water or on a hose? Hose connections going to pumps are correctly? Post some pics of the setup
  16. alldodge

    77 Carver 2866 Santa Cruz wiring help

    These are basics
  17. alldodge

    1993 5.7gi wiring diagram

    Shows its GM Being a 93 it might be close to this one
  18. alldodge

    1993 5.7gi wiring diagram

    Sounds like you need a GL instead of Gi and if its a GL then which one
  19. alldodge

    5.0GL-C won’t get on plane

    Using an advance timing light or having the damper marked so advance can be seen. Set base timing at 10* then remove shunt and verify 5.0GL-B/C/D/E Models1 Engine RPM. . . . . . . . . . . . . . . . . . . 89 AKI Fuel Initial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10°...
  20. alldodge

    77 Carver 2866 Santa Cruz wiring help

    Being that old it's not likely you can find the diagram unless Carver has it. Most likely you would just wire using the boating industry standards. Don't know if you have a Gen, but without one of those run house Bat wiring, into cabin and use buss bars then go to fuse/breaker panels
Top