Search results

  1. Lou C

    Awful Boat-Outboard Mismatch.-

    You have to hit the drop down it will show more years going way back, I even found the catalogs for my '88 H-200 in there.
  2. Lou C

    Awful Boat-Outboard Mismatch.-

    I looked round their old catalogs, there was a 195 Sundowner outboard, this is a 19.5" boat, I think the one in the pics is mis labeled, a 210 Sundowner would be 20'10" long which I don't think that one is. In fact I don't think there was ever a 210 Sundowner outboard model built. What is the...
  3. Lou C

    1992 Mercruiser 4.3L 262 CID Pre-Vortex Back Fires

    Even some of the manuals tell you to spin the pushrod, but the moving it up and down method I think is more accurate, I think friction can throw off the spinning the pushrod method. If its backfiring through the carb an intake valve staying slightly open could cause that too, from too tight...
  4. Lou C

    Awful Boat-Outboard Mismatch.-

    Take a look at the Four Winns website, there are older catalogs available on their site... When the outboard is tilted down the anti cavitation plate should be at about the same height as the keel. Talk about a bad match the trailer is even worse, that axle has to go way back for it to be...
  5. Lou C

    Winterizing

    First you have to have a hose that puts out good water pressure and is not kinked. If you're doing this at home make sure someone is not taking a shower or doing the wash at the same time because it will drop the water pressure enough to overheat the engine... Put the muffs on the lower unit...
  6. Lou C

    Cooling Intake line issue - What next?

    Interesting and not that uncommon on salt water boats. On my OMC Cobra there was a plastic water screen in the lower unit just like on the Johnson & Evinrude outboards. Because my boat is moored in salt water approx 5-6 months each season even with painting it with anti fouling paint I still had...
  7. Lou C

    1995 Volvo Penta 5.8 FSI

    I don’t know anyone who’s tried to use this system, I’ve seen a number of installs on classic muscle cars on the internet that are interesting. I think in terms of cost, complexity and availability of spare parts for boats carbs are superior. Just take a look at the complexity of wiring harness...
  8. Lou C

    5.0 GXI-N Cooling System

    Well in either case if you use muffs or the flush port you have your water pressure helping the impeller move the water. The only true test is to put the boat in the water and test it under operating conditions. Normally, the raw water hose will be full of water due to the fact that its below...
  9. Lou C

    What´s the best replacement for AQ271C (or 570) 5.7 GM engine, ideally stroker?

    They are ignorant. Vortec gives 30 hp on the V8 and if your in salt water ask that dealer if he’s ever seen the inside of a salt water run raw water cooled motor after 10 years...he does not know what he’s talking about...
  10. Lou C

    Another winterize question

    Well there is still the raw water intake hose that leads up to the heat exchanger, I'd disconnect that hose at the H/E, and put the drive down, then fill it with -100 marine antifreeze to push out any water in the hose and any coolers that are in line with that hose (p/s or fuel cooler).....
  11. Lou C

    5.0 GXI-N Cooling System

    It sounds like he said it worked on the flush port but not with muffs. Here's what I used.
  12. Lou C

    Winterizing

    You have a Ford 302 any filter that fits that engine will work. I used both Sierra and Mercruiser filters in the past, but a car oil filter like a Purolator will work fine. I like the Merc/Quicksilver oil, because I did an oil analysis and it held up very well in my use. For the drive oil the...
  13. Lou C

    Winterizing

    Also: If you’re old fashioned and like to buy stuff in person if there is an Evinrude outboard dealer near you they can order any OE parts that are available from BRP. I have a boat parts dealer who can order parts from Volvo Penta, BRP or Sierra. So one way or another I get the parts I need...
  14. Lou C

    5.0 GXI-N Cooling System

    The last ones of that style I bought (Tempo or Moeller square dual inlet muffs) the rubber was too stiff for them to conform to the lower unit contours and a lot of water was exited around the sides. The Merc/Quicksilver ones are much softer rubber and flex to the shape of the lower unit. That...
  15. Lou C

    1995 Volvo Penta 5.8 FSI

    Holley # 0-80319-2 600 CFM is calibrated for the Ford 5.8 liter (351 cu in) V8
  16. Lou C

    5.0 GXI-N Cooling System

    Try the round Merc/Quicksilver muffs with the metal steel rod clamp these work better than the rectangular dual inlet ones.
  17. Lou C

    Winterizing

    There is; get a hold of an OMC on line catalog (we can’t post other sites here so you need to search on your own) and a Sierra aftermarket catalog for parts you can’t get from OMC/BRP. I’m sure you can get stuff right here on iBoats, look around. Keep in mind that Volvo Penta also used the same...
  18. Lou C

    No Power at Ignition or Instrument Panel

    Check the fuse for the ignition circuit, I had a similar problem where I had some oxidation on the fuse and no power to anything but the trim system. Pulled out the fuse put it back in and everything worked! That one had me going. Check for battery volts at the B terminal (red wire) at the...
  19. Lou C

    Winterizing

    As far as motor oil you can use Merc/Quicksilver 25/40 or Rotella 15/40 or Delo 15/40 if you want something less expensive, I've used the Merc oil for a long time, for the drive you can use the Merc High Performance gear lube it works very well in the Cobra. If you are going to change the gear...
  20. Lou C

    1995 Volvo Penta 5.8 FSI

    These engines were also used by OMC and came with Holley carburetors, you'd have to find a Ford 4bbl cast iron intake manifold for the 5.8, a mechanical fuel pump (although a low pressure electric pump could be used) and as Bruce said you might have to change the distributor. Look the engine up...
Top