Search results

  1. C

    1970 4 hp Evinrude stops suddenly

    sounds like an internal clog... bad coils could fail as well as broken wires but I can't see them causing overheating with the head off see if you can probe, wiggle a nylon line (weed wacker stuff) up and in accessible water ways . try strong air pressure backwards etc... btw I...
  2. C

    Evinrude 40 HP Carburetor Help

    great ! thanks for the feedback. I would not mess with the LEAD plugs unless absolutely necessary :)
  3. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    here is some good reading.... sometimes simple things mess up..... sparkplugs, bad 55v blue condenser, vst float not working etc... https://www.etecownersgroup.com/post/hard-starting-250hp-6393195?highlight=250+hard+start&trail=15
  4. C

    2013 E-Tec 250 (E250DPXABA/S# 5396595) Hard Start

    Great ! it is now a wait and see... my 75ETEC is 17 years old with no injector issues yet but I guess anything can happen. MINd you I have less than 600 hrs on mine I would insist on getting a EMM log dump because "thinking" the injectors are the cause is just thinking and guessing...
  5. C

    2005 Johnson 115 minor annoyance this time

    well your T&T is real smooth and silent :)
  6. C

    2004 OMC 90 HP stator check

    check the web for CDI trouble shooting guide
  7. C

    Evinrude 40 HP Carburetor Help

    ok found this utube... fuel nipple is just an inlet nipple....nothing to worry about see video of the 88 40hp carb probably identical to yours :) the top idle jet is actually for AIR not fuel !! I learned something today :-)
  8. C

    Evinrude 40 HP Carburetor Help

    see diagram... see parts 6 and 9 #6 is called " fuel nipple" and obviously it must pass fuel #2 lead plug must be in #9 idle jet must be clean . I never saw a par16 on older carbs so this newer e carb body was molded for it ... it is all in your hands now :-)
  9. C

    2005 Johnson 115 minor annoyance this time

    on my 75 etec the extreme down position strains the T&T pump and the sound changes to a higher pitch telling me it has reached the extreme down position..... I then release " the button"
  10. C

    Evinrude 40 HP Carburetor Help

    I don 't see orings in the parts layout above. which hole ?? on top of the carb did you look down in ..... is it below the #2 lead plug...I do not think that lead plug should allow you to "see" down the carb otherwise the carb would suck air and null out the idle circuit functions on the...
  11. C

    Evinrude Mate 2 HP Driveshaft

    does water get in the GC...? maybe best to look for a spare shaft or just change the oil mid season if it does leak some welding shops can " blast" weld" the groove away $$$$ but not very cost effective on a 50 y old motor. oil is cheaper :-)
  12. C

    Johnson 90hp alarm buzzer

    wiring example up to 1995 but it shows the basic principle of yellow/reds
  13. C

    Evinrude 40 HP Carburetor Help

    great find... looking at that drawing It did not show that brass tube the side channel route used for ages does not seem to used on this carb if an internal feeder tube is used to route fuel to the upper LS jet and drip chamber. In any event I think you are on the way to happiness :-)...
  14. C

    Evinrude 40 HP Carburetor Help

  15. C

    Evinrude 40 HP Carburetor Help

    the engine sucks " idling" fuel from the bottom of the carb bowl via a very small side channel leading up to that drip chamber under plug#5 make certain you have the proper gasket to accomodate the side channel feed route because some "similar" gaskets (depending on the kit) do not have...
  16. C

    What would you pay for a parts motor

    as boomers get older... give up on their favorite sport and the x & y's don't care about sitting hours fishing without their fingers punching away their lives on facebook, instagram etc.... a lot of 30-40-50 old perfectly good motors sit in the sheds till the great reaper comes with...
  17. C

    1959 Glastron need to find a starter solenoid

    measured 12v could be highly resistive from oxyidized cable crimps and connections preventing the amps from flowing properly. did you clean all connections properly ?? did you try a fresh 12v of the the battery with a jumper cable directly on the starter +12v post ?? .Assuming the...
  18. C

    What would you pay for a parts motor

    my really nice & really clean locked up 9.5hp was $50 cdn and lives !!!
  19. C

    2005 Johnson 115 with low compression: noob seeking wisdom

    normal 2 stroke oil-fuel unburnt floating the barrel ... that is why lots of admins want 2 strokes of their lakes !!
  20. C

    High RPM surge driving me nuts!!!

Top