Search results

  1. Keyboardman

    '96 Evinrude 200 wouldn't rev past 4k RPM

    Always OEM parts. I have a air gap spark tester, I'll test each cyl and see if one looks weak.
  2. Keyboardman

    '96 Evinrude 200 wouldn't rev past 4k RPM

    The voltmeter on the dash is in the green showing around 13v, I don't understand what you mean when you're saying "Have yet to have a bad coil not pass the ohms test." Are you saying that a bad coil can read good ohms and still be bad? There are no cracks or any signs of deterioration on them...
  3. Keyboardman

    '96 Evinrude 200 wouldn't rev past 4k RPM

    All the coils check out to spec with an ohm meter. This in not a FITCH engine, just has 6 hungry carbs. No overheat warning or fuel restriction alarm. I've experienced that before with a clogged water separator. I have replaced the timing base and stator, and and rebuilt the flywheel a couple of...
  4. Keyboardman

    '96 Evinrude 200 wouldn't rev past 4k RPM

    Hi all, the engine was running fine for about 30 mins between 4500 and 5500, I slowed down to idle thru a No Wake zone for 10 mins then when accelerating back up, it was very slow to respond and would not go past 4000 rpm. The tachometer needle would occasionally drop down to zero and back up...
  5. Keyboardman

    96 johnson 150

    I have a 1996 Evinrude 200 Ocean Pro and it only has 105 to 100 psi. It also runs like a Tiger pushing my old 21' Dixie WA to 43Mph. : )
  6. Keyboardman

    94 Johnson venom 200 Bogging in forward

    Check the magnets on the inside of the flywheel while you have it off. I had a bunch come loose. They are only epoxied to the flywheel and can and will come loose and move out of place.
  7. Keyboardman

    94 Johnson venom 200 Bogging in forward

    Is the timing base moving freely? It should start to move before the throttle plates open. I had one get sticky from goo leaking down from a stator once.
  8. Keyboardman

    Johnson 50hp swap to a Johnson 110hp Possible?

    "DIRECTLY SWAP" is what the guy asked. I would assume that would mean the bolt holes too. What's wrong with you guys?
  9. Keyboardman

    Johnson 50hp swap to a Johnson 110hp Possible?

    Yeah, all the guy asked was will it bolt up and that racerguy seems to be obsessed with taking and posting compression numbers.
  10. Keyboardman

    Johnson 50hp swap to a Johnson 110hp Possible?

    Huh??
  11. Keyboardman

    1988 Bayliner Capri 2.3 ford engine

    If it's a freshwater boat then the exhaust manifold and riser are worth a few of hundred bucks as they are NLA and the Cobra outdrive a couple too, but it's limited to just the 2.3 engine. For the rest of the boat and engine, drop it all off at the landfill.
  12. Keyboardman

    Rebuilding Carb kits advice needed

    So I found the OEM kits with floats for about the same price as the Sierra kits without and will go with them. I guess it can't hurt to replace the floats while I've got them tore down.
  13. Keyboardman

    Rebuilding Carb kits advice needed

    Hi all, I'd like to rebuild the carbs on my '96 Evinrude 200 Oceanpro during the off season. I see OEM kits with new floats and also aftermarket kits without the floats for a little less money. Should I bother replacing the floats when rebuilding if there's nothing wrong with the old ones...
  14. Keyboardman

    1987 Bayliner Capri 1950 OMC Cobra bowrider starter bolt broke off.

  15. Keyboardman

    1987 Bayliner Capri 1950 OMC Cobra bowrider starter bolt broke off.

    So maybe the starter is held in place with just Two bolts from now on and not worry about getting it out. : )
  16. Keyboardman

    1987 Bayliner Capri 1950 OMC Cobra bowrider starter bolt broke off.

    I think removing the engine might be a bit much. There's got to be a way to change out the starter without removing the engine. Just because a bolt broke off shouldn't stop the starter from coming off. I'm remembering an old OMC 3.0 would have three bolts, two on the bottom.
  17. Keyboardman

    Best boat lettering removal?

    I own a small sign shop and we do custom boat graphics a lot. Today's digitally printed vinyl like 3M Controltac will come off using a little heat and leave little to no adhesive residue. Older lettering jobs that are just applied cheap vinyl can be a challenge to remove from time to time...
  18. Keyboardman

    Airbrushing graphics?

    Digitally printed Vinyl is the way to go. I own a small sign shop and we've done quite a lot of custom boat graphics. They will last for years and are removable if you sell the boat later on down the rd. If there's no local sign shop around you may find some stock graphics online.
  19. Keyboardman

    Adding ballast to the bow?

    I'm not sure what you're talking about. Nobody has butchered up anything on this boat. The fuel line and wires coming from under the deck and the bilge are routed up thru the factory fittings. The bilge access hatch is factory too as verified by a picture of one other outboard version of this...
  20. Keyboardman

    Adding ballast to the bow?

    Definitely on a bracket. It's not a flotation style bracket, it's open on the top and also a hole in the bottom of it. The deck drains go thru the transom and into the bracket.
Top