Search results

  1. ab59

    distributor cap question ---

    Another stupid question I'm sure but I can't seem to find the answer anywhere. I have a Mallory dist. part # 4748201-H on my 5.7 gm engine, 1988 vintage . I want to change out the cap and rotor . Is the cap and rotor the same for an electronic ign as it is for a standard points dist. ? |The cap...
  2. ab59

    1988 Omc Cobra 5.7 --where should my electronic choke be wired to ?

    I currently have my electric choke wired to the side of my coil . I have read somewhere that it is not correctly connected by doing this. I do not have an original alternator on the engine but seems like I was not supposed to go to the alternator either. Sooo where is the correct place to hook...
  3. ab59

    5.7 difficult to start on and off --- Any ideas ?

    Hey guys , was out fishing yesterday and have been working out a few bugs in the engine and have figured out a few but the engine not wanting to start every time has me a little stumped. It will fire right up one time and then sometimes I have to crank on it for quite a while before it will...
  4. ab59

    OMC oil change Problems---- wrong filter ?

    I finally ran the boat long enough to put a few hours on the new 5.7 engine so I wanted to change the oil and get the break in oil out . I bought a Cobra Marine Filter some time back that was advertised as being for a 5.7 engine . Well although it threaded on just fine it leaks like a sieve...
  5. ab59

    1988 5.7 OMC Cobra--ESA Influence

    Took my boat fishing yesterday with a couple of shirttail relations and began to have a few bugs show up in engine performance . After tooling out past the 5 mph buoy I opened up the throttle and had one pop and a miss now and then , when I backed off a little it ran smoothly . That was the only...
  6. ab59

    battery question

    I put a new 31 series battery in the boat a few months ago that I bought at Wally World and fully charged it now reads 11.27 volts. I used two different meters and both read the same. The engine starts fine , it seems to hold a charge and I have not really had any problems yet. Should I return...
  7. ab59

    Omc Cobra shift problems---- 5.7 1988

    Well , I set the idle at 600 rpm and then I reset the throttle . A little better but still does not want to come out of gear when in the water, on the muffs it shifts in and out of gear just fine . The following pictures are the positions of the detent in Neutral then WOT in Forward, then WOT in...
  8. ab59

    Omc Cobra shift problems---- 5.7 1988

    Just when I thought I was done with this project I find that I still have a shifting problem. I replaced the engine and transom shift cable and used the OMC jigs to set the cable up so I know it's right. I adjusted the control cable according to Wolfs directions . I can shift into gear 9 both...
  9. ab59

    my new old 1988 ss20v

    Took the side guides off and replaced what was rotten and rapped em in some new marine carpet. I think the plan will be to finish out the buffing ( I may try some color sanding at the bow to see if i can get rid of the rock chips ) and then roll under the trailer and take the staples out of...
  10. ab59

    my new old 1988 ss20v

  11. ab59

    my new old 1988 ss20v

    Looking more like a finished product all the time Lots of odds and ends to take care of but with a few more nice days it will be a done deal . :joyous:
  12. ab59

    my new old 1988 ss20v

    Another nice day other than more wind . Got the rub rails finished up and tried to tie in the carpet where the stern cap meets the gunnels . Will see tomorrow how it looks after the glue dries . Pulled the bottom of the doghouse in and mounted it, still have to re re re cover the turtle shell...
  13. ab59

    my new old 1988 ss20v

  14. ab59

    OMC Cobra failure to start .

    Finally got a couple of pics to load.
  15. ab59

    OMC Cobra failure to start .

    I have got my boat to the point where I need to start and run the engine as well as test the shifting adjustments that I have made after a new transom cable was installed. I set the Tsm cable up with the OMC jig but after assembly would not shift into reverse . I thought I had solved that...
  16. ab59

    OMC Cobra Bell-crank 1988

    here is my upper cable end
  17. ab59

    OMC Cobra Bell-crank 1988

    Neutral---
  18. ab59

    my new old 1988 ss20v

    Well , as usual the minute I got out the paint the wind came up ! I don't know what it is around here but it's as if some one with the power to control the wind is watching and just waiting to fire up the wind when I start to paint something on this boat. :confused: Anyway It is what it is now...
  19. ab59

    my new old 1988 ss20v

    Finally stopped raining here and I've had a couple of days to work on the boat again. Had a few problems with the shift Bell Crank among other things but it's all good now . Wet sanded and primed the outdrive today and will install the end on the transom shift cable before and hook the shift...
  20. ab59

    OMC Cobra Bell-crank 1988

    forgot a picture----
Top