Search results

  1. tg3690

    1990 force 90 hp trim pump kit?

    Once I had rendered the valves unusable, put them in a vise and used vice grips to try to take them apart.......never did get the caps off.....literally broke in half, totally destroyed! Lol. :ROFLMAO:
  2. tg3690

    1990 force 90 hp trim pump kit?

    Did a search on ebay, couldn't find her on there.
  3. tg3690

    1990 force 90 hp trim pump kit?

    Franz marine had one rebuilt pump left.....it was rebuilt by rRhitt (RIP). Not cheap for sure, but works perfectly.
  4. tg3690

    1990 force 90 hp trim pump kit?

    I started out real careful, went down hill from there.....lol. Got a 10 pack of those o-rings, more than I will ever use, and it only takes 2 for the repair. If ANYBODY needs a couple, let me know. (y)
  5. tg3690

    '88 Force 15 "Where's the thermostat?"

    "Give me a little credit here...damn" :ROFLMAO:
  6. tg3690

    1990 force 90 hp trim pump kit?

    Its in the stickie by pnwboat....he used Briggs Stratton kit #398188. I have some that I didn't use....ended up buying a rebuilt pump. PM me if you need some.
  7. tg3690

    '88 Force 15 "Where's the thermostat?"

    Franz has pulled me from the fire a few times.....Chrysler/Force is what he does. Great guy....816-966-8085 Tue-Fri 10 to 6 Central time.
  8. tg3690

    '88 Force 15 "Where's the thermostat?"

    Call Franz Marine Service.....he can answer your question and probably has the parts if you need em.
  9. tg3690

    FYI.....Preamplifier Problem-Solved

    Recently had a problem where my motor would start and run fine....but once warmed up and under load, it would randomly quit running, typically at higher rpms and it was like you turned the key off. No jerking or sputtering....just completely shut down. But would start right up and run...
  10. tg3690

    need starter for chrysler 70hp model 707hf availability

    Sometimes the best bet is to rebuild your original starter.....take it apart and inspect the brushes/armature. Found these parts to rebuild mine on ebay....brushes $20, armature $25. The quality of the new starters is suspect as most are made in China. Or take it to an alternator/starter...
  11. tg3690

    Merry Christmas, Iboaters!!

    Hope yall had a great Christmas despite the blizzard conditions up that way...living along the Gulf Coast, hard to imagine what that is like. Happy New Year!
  12. tg3690

    Chrysler 75 hp 1975 Spacer plate?

    Wondering why you needed to change the spacer plate.....cracked, broken? Looked at a few on ebay......the pics show some with the hole and some without.....same part number. Hard to tell from the pics....is that a blind hole or does it go into the water passage? On another note, when mounting...
  13. tg3690

    Nobody fishing?

    That surf looks pretty rough.....what were yall catching?
  14. tg3690

    1989 Ranger 350V - flotation foam

    Smart move.....good luck with the restoration. Always wanted a Ranger boat. (y)
  15. tg3690

    1989 Ranger 350V - flotation foam

    4stringbass.....does your '89 Ranger have wooden stringers and transom? Not sure when they went to all composite.....thanks.
  16. tg3690

    Been there, Done that;

    Forgettin to slide the shrink tube on before soldering......
  17. tg3690

    warning horn

    Was going WOT one time years ago......suddenly my engine started making bad sounds and stopped......only then could I hear the warning buzzer under the console.....way too late. Have installed a car type horn and a warning light....and regular impeller changes since.....
  18. tg3690

    1990 Force L-Drive: A LOT of fun but a few issues... Gear Selection & Lower End Stuff?

    Don't use ether in an old IDI diesel engine.....not good.
  19. tg3690

    Motor oil in lower unit oil

    Quicksilver 90W nearly $20 a quart now.....
  20. tg3690

    Motor oil in lower unit oil

    Put some cheap Walmart lube in it....run it...drain it. Then put in your high dollar lube. No seal damage and no cross contamination from other fluids.
Top