Search results

  1. pvanv

    Tohatsu 25 hp , 25MC2 electric starter, gray color

    346760100M STARTER MOTOR $424.75
  2. pvanv

    90hp Nissian won't open up

    It depends on your serial number, regardless of year of manufacture.
  3. pvanv

    Outboard running rough and I need help

    What method did you use to clean the carbs? If you didn't completely disassemble, soak overnight in real carb dip and then blow out with generic spray, you likely need to do that.
  4. pvanv

    90hp Nissian won't open up

    Depending on serial, you may have ordered the wrong part.
  5. pvanv

    Tohatsu 25 hp , 25MC2 electric starter, gray color

    Go to an auto electric shop and have yours repaired.
  6. pvanv

    8hp starts but runs only at high rpms

    Clearly your valves are seating. No need to lap them. I would reassemble, do a Proper carb cleaning, and then decarbon spray after it's running better.
  7. pvanv

    Tohatsu m70a water pipe

    It should be a single piece. Might be time to use some neoprene tubing to join the pieces.
  8. pvanv

    2000 m25c3 25hp 2 stroke flywheel

    No clue. Can you reattach the old magnet?
  9. pvanv

    Controls and prop for Nissan NS70A2

    Props are trial and error. Check WOT RPM to determine where you are now, and go from there. Most any binnacle control with TT switch will work. Single binnacle mount control box, with power tilt/trim switch & electric start. Control box only. For all TLDI models with power tilt & electric...
  10. pvanv

    90hp Nissian won't open up

    There is an exciter and 3 pulsers on the plate. I would test them. You want a harmonic balancer puller to get the flywheel off.
  11. pvanv

    8hp starts but runs only at high rpms

    Peter, My money is still on needing a Proper carb cleaning. I doubt you need rings.
  12. pvanv

    2004 Tohatsu 6 hp 4 stroke,Can't get lower unit back on...

    Take a break and try again. It's a matter of feel. The shaft is not aligning with the crank splines.
  13. pvanv

    2000 tahatsu 25hp 2 stroke worth

    Well, it's 20 years old, so not much. The flywheel has an MSRP of almost $500.
  14. pvanv

    8hp starts but runs only at high rpms

    You must disassemble the carb before soaking. After, blow out all passages. You may have a sticky float valve.
  15. pvanv

    90hp Nissian won't open up

    Several spots, especially in the low speed circuits.
  16. pvanv

    90hp Nissian won't open up

    Year of manufacture is irrelevant. You did not say, but you likely have an M90A. Clean the carbs with a proper overnight soak and try again.
  17. pvanv

    8hp starts but runs only at high rpms

    You can also swap to the 9.8 carb if yours won't come clean. Then you add power as well.
  18. pvanv

    Cutting out and stalling

    Temps should be about 150F. Did you reset TPS initial setting per the FSM? What are the fuel and air pressures?
  19. pvanv

    Tohatsu 9.8A3 EP no tilt lock

    Sounds likely.
  20. pvanv

    Tahatsu 30hp ptt solinoid replacement

    What is your actual model? 2 stk? 4 stk? Carbed or EFI? If 4-stk, the solenoids are on the front of the powerhead, and replacement is very straightforward. I would actually test the solenoids and verify wiring before replacing them willy nilly. Full info is in the Factory service manual.
View older results
Top