Search results

  1. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    While I was at it, I'd planned to fair and re-gelcoat some beaching damage by the bow. However, with the trailer out, I found much more expansive damage. There was/is stress-cracking and evidence of running aground throughout most of the hull, which was covered by bottom paint. It's not deep...
  2. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I can't believe how long it's been since I updated this thing. Work never stopped on the boat, just went slower than I'd like due to lots of overtime at work. I'll try to recap in order based on old pics in my phone: I re-covered the cooler seat: I then focused on slightly modifying and...
  3. eggs712

    1981 Springbok 18' Restoration/Renovation

    Those welds will hold just fine from what I see. Most aluminum welds crack from the crater being underfilled and/or work hardening from repeated stress.
  4. eggs712

    Time to dive back in - transom and deck replacement

    I would look up the technical data sheets for the honeycomb panels versus other materials. Honeycomb panels tend to be good in compression, but poor in other specs. It may still work, but could require other alterations to achieve the same strength as original.
  5. eggs712

    Replacing bow seat foam

    A 24 TPI hack saw blade works well if you don't want to buy a new tool.
  6. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Ouch, it's always something eh. Still no lake to test this boat on, so I may slow down soon.
  7. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    It was already there, so I was stuck with the hole; I believe it's factory from my searching. I did replace it with an aluminum frame version, but I don't recall if I posted it. It's strong enough to be stepped on, but I'm still going to sew up a protective/insulative cover for it. Any...
  8. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Next, I decided to add a decent, albeit budget sound system in the cockpit after being underwhelmed by the soundbar in my bay boat. I added an 800W Skar monoblock amp plus an 8 channel Rockville 600W amp, one 10 inch DVC Skar subwoofer, and four 6.5 inch Skar coaxial speakers. The aft speaker...
  9. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    The headliner is done, minus adding some trim where edges meet. You can also see the Sunbrella curtains I made plus the pieces covering the hull/cap joint (not sure of terminology). When I replaced the rub rail rivets with #10-24 bolts, I installed really long bolts every couple of feet...
  10. eggs712

    Bought Boat and Steering is locked up

    I have unfrozen several cables by attaching ATF-filled clear vinyl hose to the end of the tube. With the hose pointed up so that the fluid enters the tube, rig the other end up to compressed air. It sometimes takes a week, but it works.
  11. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Thanks! It's sold as 'outside corner trim' at the big box stores, 1.25" outside and 1" inside; the added insulation and such required 1" deep trim. The way I've redone the headliner is probably 10 times the work of just going back with hull blanket/carpet, but my nearby lake I wanted to test...
  12. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I pretty much finished the overhead of the V-berth minus the trim ring for the escape hatch; I purchased a used aluminum hatch trim ring on ebay I'll have to cut down and weld back together, but I'm saving up welding projects for one long weekend. The windows are trimmed with PVC, and I sewed a...
  13. eggs712

    Trolling motor shaft support.

    I added a stay/shaft support to mine after hearing stories of trolling motors breaking off at the mount and/or damaging the fiberglass from choppy seas. It also helps on bumpy roads when trailered.
  14. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    Where the alcohol stove once was in the galley, the PO placed a plastic bin that looked unsightly and didn't cover the entire hole. I replaced it with an inset cabinet/bin out of stained 1/2" plywood with an acacia cutting board top.
  15. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I finished fully insulating the cabin, which allowed me to run a space heater more effectively in some frigid temps last week: I also made up my mind on how to tackle the V-berth's overhead. I glued many small plywood furring blocks in strategic spots to help bypass some of the compound curves...
  16. eggs712

    What Is everybody using for spark plugs

    When I couldn't find NGK plugs locally, the Champion L76V worked out fine.
  17. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    I wish I could pretend it was my idea! I'm always scouring forum archives trying to find good ideas
  18. eggs712

    1985 Bayliner 2750 Ciera Sunbridge Resto

    The fore deck hatch/emergency escape I remade early in this project developed a crack in the glass last year from the hole I drilled in the glass; it was a single crack that I could live with, but last spring, the glass sprung more cracks after some weather changes. Instead of ordering new...
  19. eggs712

    changing transducers and fishfinders.

    I have a couple Echomap Ultra 106SV units. Bass Pro/Cabelas has them at $1000 with the GT-54 transducer. I like the touch screen plus buttons for when it's choppy. The GT54 reads bottom well at speed for me until about 250 feet deep, and the Sidevu is okay until about 100 feet deep at 460kz.
  20. eggs712

    My 84 4winns horizon 195 project.

    I bought a roll of 1/4" PE foam for the same purpose. It's a decent insulator, closed cell, and relatively inexpensive. I'm just using Dap Weldwood to glue it to the hull.
Top