Search results

  1. SHSU

    1988 Starcraft Mariner MR 220 V rebuild

    Know anyone with a media blaster? I had the exterior and some of the interior done that way. I didn't have foam, but the media blaster should make short work of any as well. SHSU
  2. SHSU

    1979 Starcraft 16’ SS Refresh

    How did you secure the top: blind? Same holes as the original? Did you add any extras? SHSU
  3. SHSU

    21' Holiday Rebuild

    Ya, if I had known I was going to spend as much as I did on the rebuild I probably would have walked away.... That being said, I wouldn't change it and we love how it turned out. Plus I literally know every square inch of the hull/engine. So if something breaks I know how to fix it. SHSU
  4. SHSU

    1988 Starcraft Mariner MR 220 V rebuild

    Can't hurt to try with power washer, but would still want to wire wheel back behind the foam. Want to make sure all the corrosion is out and no pitting is hidden under anything. SHSU
  5. SHSU

    1979 Starcraft 16’ SS Refresh

    What!?!?!?!?!?! No Pictures!?!?!?!?!?! lol Man those look great!!! What length did you go for in the end? It depends on how it sits up front and if you let it get that low. As you get on plane the front end is going to be higher then the back, so your fuel will move to the rear. I have...
  6. SHSU

    1979 Starcraft 16’ SS Refresh

    I didn't add any when I put ours back together. We haven't noticed an issue or noises but might also be because we have the front anchor cleat that goes through it and secures the aluminum straight to the wood. I like it!!! I would have done something like that if the admiral didn't want to...
  7. SHSU

    1st boat - 1981 Starcraft SS 160

    Just make sure to torque all the bolts to spec. I didn't in some areas and it caused issues..... Couldn't figure out why it would run like a champ at idle but when I tried to give it gas it would die or just sputter with no power. Turned out I had forgot to torque the intake manifold and...
  8. SHSU

    22' Islander rebuild

    If you want another grandkid I am available!!!! LOL Very nice, a lot of memories to be made. SHSU
  9. SHSU

    21' Holiday Rebuild

    There are a lot of options for non skid out there. Rustoleum and other companies sell additives you can add to most paints. Also, if you plan on adding the non skid material to the final coat of epoxy that might give you a long lasting non skid that can be repainted over time without worry of...
  10. SHSU

    1978 18ft Mariner: Getting Ready for June 2021 Splash..!!!

    +1 with @Watermann Replace the seals even thought it still looks good. It sat that long, I wouldn't trust the seals to last much longer once put to work. I would do the shift lever seal, driveshaft seals, prop shaft seals, new oil bolts washers, and new impeller. SHSU
  11. SHSU

    1979 Starcraft 16’ SS Refresh

    Make sure to take lots of pictures!!!! SHSU
  12. SHSU

    1978 18ft Mariner: Getting Ready for June 2021 Splash..!!!

    Man, sounds like you got lucky with not getting hurt. I purchased a Harbor Freight Engine lift to use and then gave it away when I finished the project. Even then it was a bear to use because I didn't account for the front bracing on the motor lift and it running into my engine stand... Live...
  13. SHSU

    22' Islander rebuild

    Is that the original door to the front cuddy? Do you have a toilet up in there or just "bedding" area? SHSU
  14. SHSU

    21' Holiday Rebuild

    Yep, that bracing follows the battleship scene. LOL SHSU
  15. SHSU

    1st boat - 1981 Starcraft SS 160

    @Dacranks You have gotten a lot of good advice on the motor. So sounds like you are on the right track. If you have never pulled one of these apart (It was a first for me), look at getting a Seloc or similar manual for info and troubleshooting. Also, look up Brandon's Garage on YouTube...
  16. SHSU

    1988 Starcraft Mariner MR 220 V rebuild

    Sadly think you had the right idea with the shovel. I have seen people use cheap roto tillers, but that was on a large ship and had literal rooms filled with foam. SHSU
  17. SHSU

    1979 Starcraft 16’ SS Refresh

    Not needed and may cause other issues. The cracking would occur from the wood expanding and contracting based on temperature and such. Also how loads are distributed would play a major role in any failure: i.e. a point load not distributed SHSU
  18. SHSU

    1979 Starcraft 16’ SS Refresh

    Ya, West System is steep but has a huge name in the industry. I tried Fasco just because it was $55 a gallon back when I did it. Think they bumped it to $75 now. Been happy with the results and their customer service was quick and courteous with any questions I had. As for the glass, main...
  19. SHSU

    1978 18ft Mariner: Getting Ready for June 2021 Splash..!!!

    Look forward to following the thread!!! Similar motivation to make memories with my wife and daughter. Since our splash, we have had a blast fishing and tubing. Nothing like cruising around on a boat you rebuilt. SHSU
  20. SHSU

    1st boat - 1981 Starcraft SS 160

    The SELOC manual I have says there are no printed specs for exact compression measurements, but cylinders should be at least 100 psi. Also, you are correct that within 10% is generally accepted. If the engine has been sitting awhile, might be good to poor some oil into each of the cylinders...
Top