Search results

  1. Scott Danforth

    Finishing before gelcoat

    On a properly encapsulated deck, the deck covering is immaterial. I would run a snap-in carpet (easier to take out and clean or replace) and never hesitate
  2. Scott Danforth

    Cabinet doors?

    Did you contact Larson? Or look in sites like great lakes skipper?
  3. Scott Danforth

    Fuel pressure

    Sitting for 3 years, the stuff in the tank was reduced to goo Did you clean out the tank after pumping it out? If not, the 25 gallons of fresh fuel just rehydrated the goo
  4. Scott Danforth

    2004 Glastron 213 cc fuel sending unit

    Do some trouble shooting prior to spending money. Most times there simply is corrosion on the terminals at the gauges.
  5. Scott Danforth

    installing these on my 74 chieftain 18

    The Amazon switches will fall apart after a while. I would suggest Carling or Otto. While Otto is the gold standard, Carling is the Sterling standard at 40% the cost https://www.digikey.com/en/products/detail/carling-technologies/AV1-1A211E-R00/11587004
  6. Scott Danforth

    1997 Wellcraft 29.5 Scarab rear seat restoration

    Use the old foam and the witness marks in the hull as a guide.
  7. Scott Danforth

    1997 Wellcraft 29.5 Scarab rear seat restoration

    Probably 1/2". I would switch to PVC board
  8. Scott Danforth

    Mercruiser starter replacement 350ci

    Depends on if it's direct drive or PMGR Depends on if it's for a 153 tooth flywheel (straight across) or 168 tooth (staggered) Depends if you are buying from GM or paying the markup thru Mercruiser, or from Arco, Remy, etc
  9. Scott Danforth

    Can’t get on plane

    Check the anti-siphon valve
  10. Scott Danforth

    Dribble of oil at prop, usual suspects checked, now puzzled

    I use this https://www.amazon.com/Mityvac-MITMV8500-Silverline-Automotive-Vacuum/dp/B0002SQYUA
  11. Scott Danforth

    Gas

    What trouble shooting steps? Did you check the anti-siphon valve? Did you check the pickup tube?
  12. Scott Danforth

    Lost gas cap

    I would buy a new filler, and drill new holes in either the boat or the filler neck flange
  13. Scott Danforth

    Gas

    Could be a bunch of issues. What trouble shooting steps have you done?
  14. Scott Danforth

    Gipsy - 1996 Sea Ray 210 Bowrider restomod

    And what does this have to go with the OPs thread?
  15. Scott Danforth

    Replace mount

    If there is no rot, then it's good. However most old fiberglass boats need a hull restoration
  16. Scott Danforth

    Everything done but low rpm at WOT. Distributor spring?

    And Holley has a 10% discount if you want their emails
  17. Scott Danforth

    Gipsy - 1996 Sea Ray 210 Bowrider restomod

    You may want to do some reading on design life vs service life. https://forums.iboats.com/threads/perspective-of-fiberglass-boat-design-life.683703/
  18. Scott Danforth

    Everything done but low rpm at WOT. Distributor spring?

    And where in the add does it state what it is other than a 4160 which is available in 390 to 750 CFM
  19. Scott Danforth

    Gipsy - 1996 Sea Ray 210 Bowrider restomod

    If it makes you sleep better.
  20. Scott Danforth

    7.4 flame arrestor to KN

    Stickers go on the tool box
Top