Search results

  1. acadian2022

    1980's serial number / harness / general questions

    hi I have the engine up trying to figure out how to remove the single ram to have it repaired one stripped hydraulic fitting at the top and not sure if the ram can be removed without taken the engine off the boat. I started a seperate post for that here are pic of the power trim
  2. acadian2022

    power trim removal of center cylinder

    I was thinking about that... and have such a tool :) what the heck will give that a try thank you...
  3. acadian2022

    power trim removal of center cylinder

  4. acadian2022

    power trim removal of center cylinder

    perhaps the center hole is a reverse tread bolt that is required?
  5. acadian2022

    power trim removal of center cylinder

    hi all. I assume I need a puller of sort my concern this is was used as a salt water engine and when I removed those covers to expose the center pin with center threaded hole I'm assuming it's going to seized had slat deposits inside of the cover. will spray penetrate WD-40. I have another post...
  6. acadian2022

    1980's serial number / harness / general questions

    good morning sorry for the delay added pic will add more today.
  7. acadian2022

    power trim removal of center cylinder

    no problem. thank you
  8. acadian2022

    power trim removal of center cylinder

    hi. it's a hard one to figure out have another post open but we think 1982 V6 200 HP
  9. acadian2022

    power trim removal of center cylinder

    good day all. could someone explain how to remove single center cylinder for a replacement see pictures. I see the top part will be a pin to knock out its the bottom one not sure how to go about it. thank you all
  10. acadian2022

    1980's serial number / harness / general questions

    Thank you for the feed back I have to say regardless of seeing the old 200 decal under the new decal I can't argue that it's a 200 or not, seen some strange scams in my lifetime.... will check sensor location you suggested and can take as many pictures as need to confirm if this outboard is a...
  11. acadian2022

    1980's serial number / harness / general questions

    hi all. you could see the old decal on the hood under paint also 200. the serial tag and the frost plug has the same number as mention on my first post.if this help the heads no is 95081. another question is it possible this engine didn't have an actual temperature sensor reading on line where...
  12. acadian2022

    1980's serial number / harness / general questions

  13. acadian2022

    1980's serial number / harness / general questions

    Good morning all. when reading some replies my Merc included a cluster of gauges oil PSI / Volts / temp / tac and fuel level. can anyone confirm if this outboard has sensor for oil PSI / Volt fuel I'm aware its seperate. the harness that was included is an 8 pin plus 4 that was confirmed as to...
  14. acadian2022

    1980's serial number / harness / general questions

    Thank you thank you... do you have any knowledge about the fuel mix setup they had vs original dual tank? if anything should have been bypassed fuel pump etc properly for me to ensure it was done correctly. I will add a few more question to my original post regarding power trim system.
  15. acadian2022

    1980's serial number / harness / general questions

  16. acadian2022

    1980's serial number / harness / general questions

    Good morning. its a 200HP and was fully restored new paint decal etc that is why it was confusing to me on my end also when looking at picture and couldn't find it by using the serial number. thank you so much all for any info
  17. acadian2022

    1980's serial number / harness / general questions

    Good morning all. I have a multiple questions regarding a Merc fully restored I just purchased. serial number 6033659 cant find a conclusive year online yet. Questions. 1. year ? 2. harness is an 8 pin plus 4 wires ( grey = ? ) ( purple = ? ) ( black yellow stripe = ?) ( yellow red stripe =...
  18. acadian2022

    1987 GM 305 x 2 rebuild questions.

    Ok perfect will buy 2 thank you sooooo much Scott...
  19. acadian2022

    1987 GM 305 x 2 rebuild questions.

    Good day all. Do anyone know if I could use the balancers from the 305 for the 350 block? Reason I'm asking only one of the two 350 had a balancer and the 350 balancer is bigger then the one from the 305. Thank you all. If so wanted to keep the shaft and crankshaft with the 350 engine and use...
  20. acadian2022

    1997 Doral 300 SC twin 5.7 mercruiser

    Good morning all thank you all for the suggestions all is noted and will try everything that was pointed out. I do have a digital compression tester on the to do list to check all cylinder compression. will keep you all updated have a great day.
Top