Search results

  1. C

    Filter for main 2 cycle oil resevoir

    Update......There IS a small inline filter UNDER the 2cycle oil reservoir.Yes under the reservoir.Simple to replace AFTER you unbolt the reservoir retainer/tiedown/boltdown and lift the reservoir out of the compartment housing it.(way easier if reservoir is emptied) Turn the reservoir on its...
  2. C

    Filter for main 2 cycle oil resevoir

    2000 200hp Saltwater series sxt200 .I have seen that there is a filter on the bottom of the main oil resevoir tank on some models.I dont see it anywhere in my clymer manual.My tank does not look like it has ever been removed so before I tackle the mounting bracket,does anyone know if certain...
  3. C

    Pee hole only dripping water --- 15hp Tohatsu

    Pull the Tstat and replace.Also try pushing a piece of wire into the exit hole as far as you can ,.You may have it clogged with silt from running in murky or shallow water.Charlie
  4. C

    stain on gelcoat from wet leaves

    Dingbat.... Im Def not confusing products.Both products do the exact same job on fouled fiberglass.I am surprised to see that you have never seen a post here suggesting this.Do a search to satisfy any curiousity.Marykate on-off $20 a bottle and Toilet bowl cleaner $1.00 a bottle do exactly the...
  5. C

    1970s Mako 17

    btw look inside your console for your gas tank.You should be able to get to the top of it.If it is metal then it is original and probably going to need to be replaced sooner or later if not already.Charlie
  6. C

    bilge pump

    Try to duplicate the pump that is currently installed.never go with less gph output,Charlie
  7. C

    1970s Mako 17

    I have same boat 1984 and have had it for 20 years.The boat is a beast!! I have had it out safely in weather that my fellow boaters with 25 ft boats wouldnt leave the dock in.There were a few cracks n the fiberglass in the stern and friends told me not to buy it....That was 20 years ago and the...
  8. C

    stain on gelcoat from wet leaves

    DONT USE TOILET CLEANER!!! . Put some old fashioned bleach,not the concentrated,not the splash proof,just regular bleach in a spray bottle.Spray the leaf marks and have a garden hose in the other hand and give the bleach approx a minute or two tops to work.Rinse immediately after that.Works...
  9. C

    1970s Mako 17

    looks like a deal!!
  10. C

    A couple of different winterizing questions.

    buy a Camco kit and follow directions.you can either pull the Tstat for the procedure OR run engine until warmed up and introduce Room temp AF combined with HOT water to assure Tstat stays open.Charlie
  11. C

    Yamaha V6 Excel LH Engine sputters

    see if it has an o2 sensor.My year 2000 does. within the housing there is usually carbon build up that needs to be cleaned .There is also a pin shaped like a small barbell that needs to have the center cleaned out with a small drill bit.Post back.charlie
  12. C

    Stalling '89 225 Yamaha Excel

    diaphram fuel pumps,change them.they are cheap and easy to change.Less than $50 each.Charlie
  13. C

    Cleaning O2 sensor

    fixed an issue by cleaning the o2 housing .Figured I would clean the o2 sensor since I didnt have the correct socket to remove it for inspection.Thanks Charlie
  14. C

    Yamalube marine grease

    I have used Walmart marine grease for years and years on EVERYTHING and I mean everything.I did see red grease on my relatively new trailer wheel bearings so I am sticking with that red grease for those wheel bearings so not to mix different greases as they are not all compatible.Charlie
  15. C

    Best adhesive remover?

    I had very good results using a rubber wheel on a drill.I also has a smaller job than you have in front of you.Charlie
  16. C

    Cleaning O2 sensor

    I dont have the proper socket to remove the O2sensor. I serviced the pin within the housing which was easy enough to get to.With the O2 sensor still within the housing ,is it a decent idea to spray clean it with carb cleaner.Any downside to it?? besides being a little messy. Charlie
  17. C

    2000 200hp Saltwater series 2 stroke ticking noise

    Wasnt sure i heard anything till i removed the engine cover while idling.Stbd side ticking noise.Everything else seems just fine.Pulled plugs and all looked exactly the same.Not too familiar with Yamaha.Anything to look for before I do a compression test? Had this for 2 years not pushing a heavy...
  18. C

    Got my 1st gas Pressure washer,hope I got enough psi

    I have always bought electric pressure washers but they always seemed to lack some power.Not bad but certainly not GREAT. I saw what looked like an excellent buy .Westinghouse 2700 psi with a 212cc motor.I was about to purchase a Westinghouse 3200 but when I compared the 2 i noticed that they...
  19. C

    Have fuel /water filters gotten trickier to screw on???

    I have been doing this for a very long time and never an issue screwing on a filter.Today I replace both filters on my twin 5.0 XLs and neither screwed on in a simple manner.Are they making these things in a cheaper way causing them to be more difficult to screw on or am i losing my patience in...
  20. C

    Bearing buddies....hard to install???

    Had a new axle and hubs put on my trailer last year by local reputable trailer shop.I didnt realize until recently that there were no bearing buddies on the new axle , only dust caps.Trailer shop handed me new pack of bearing buddies when I went back and mentioned it.Problem is I cant seem to...
Top