Search results

  1. M

    Testing Gas Flow on 82' Wellcraft Sterndrive

    I would get the model ,serial number off the current distributor then have a auto parts store cross reference it . Or Google it . I'm guessing it's from a 3.0 - 4 cylinder engine . Mercruiser did not have them made special , they came off the inventory shelves . If you research- Google your info...
  2. M

    Chain worth it?

    Using line will also absorb more wave action vs chain as it stretches a bit before maxing out. It's less stressful on the deck hardware and not so jarring to passengers while onboard .
  3. M

    Testing Gas Flow on 82' Wellcraft Sterndrive

    I would install a electronic distributor before putting a Petronix system in . See them online for 120-150.00 , which is less money than the Petronix set up .
  4. M

    Testing Gas Flow on 82' Wellcraft Sterndrive

    A remote 5 gallon jug with hose hooked up to wherever you deem easiest junction pre fuel pump . Engine runs OK, you backtrack from the fuel line or start at the sending unit on top of the fuel tank. Runs the same , at least you've ruled out fuel delivery as the issue.
  5. M

    1973 Gibson houseboat oil cap

    See post # 5 . If your low on oil you have a leak . And if your real low , air will have entered the system , which means bleeding the air out . They sell a hose ( on- line or maybe on this site , around 30.00 ) that goes on the two relief valves on the steering cylinder , this eliminates about...
  6. M

    1973 Gibson houseboat oil cap

    Sea Star helm , usually fill hole goes directly into main chamber . I see a mesh reinforced hose , if that hose goes to your fill plug the oil level is good as long as oil is in that hose . Should not use or need oil , unless you have a leak , which will leave a puddle , oil spot under it ...
  7. M

    1973 Gibson houseboat oil cap

    Edit above post . OP doesn't state how for from the " steering wheel " it is . If it's within a couple inches of the steering wheel shaft then fill it as stated above as it's not some remote fill system. Through me off when he stated it's on the dash , which can be where the gauges are or where...
  8. M

    1973 Gibson houseboat oil cap

    Probably a Sea Star system, which you can buy there steering oil , 30ish a quart online . Or you can use any light weight oil #5 ( hydraulic oil like they use for snowplows )and under . Transmission oil will also work. Fill to about a 1/2" below the cap , that's for expansion in the hot weather...
  9. M

    Anodes for Yamaha outboard...Zinc or Aluminum?

    And that has what to do with the OPs question ? Can't wait to read someone's post about how they keep their boat on a trailer and don't have any corrosion issues .
  10. M

    Anodes for Yamaha outboard...Zinc or Aluminum?

    It's good you put the correct ones on . Maybe if you researched it awhile ago and got the correct material you wouldn't have any pitting .
  11. M

    Anodes for Yamaha outboard...Zinc or Aluminum?

    Are you slipped at a Marina , on a hook , private dock ? Ask any fellow slippers what they use or have the same results as you ? Stray electrical current will not affect your motor while underway , so that anode is normal to show no wear . I might try to figure out a way to have both types...
  12. M

    1999 Wellcraft Excalibur

    It's possible it was ordered with a big block. Not that unusual for a 21 + - to have them . In theory the 454 will last longer than a small block. You are working the motor less to achieve the same speed you would with a small block. So if you properly maintain it you should get 5-6k hours out...
  13. M

    1989 Astro Quick Fire

    A test light is in most boaters tool boxes . Are you getting power to the switch ? Do you have power coming out of the switch or ower at the trim pump . Your switch may be fine , you could have a bad solenoid on the pump a bad connection , worn wire or bad switch . All traceable with a test light .
  14. M

    Hardtop project

    Shouldn't be , if it is fairly level with the shearline of the hull , as in it's pretty much pointing straight into the wind when going fast . They have them on CCs that run 70 mph all day long among other hull designs Definitely aluminum for roof material , for a thousand reasons. .
  15. M

    Listing to port side

    Might want to read all the responses before chiming in . Post # 12 gives you the beam along with the HP rating ( although that's not clear if it's for that particular hull or a larger one ) . Bottom and modifications have been discussed as well .
  16. M

    Listing to port side

    I would try sanding off the lip of the hook so it looks like a continuation of the hulls bottom . Then after putting a tab on the port side , the wider the better , take it out and see how she rides . If still listing a bit , remove the rest of that section. Leaving it on will ,in a small way...
  17. M

    Listing to port side

    The hull appears to be very narrow , which in itself will list quicker and more severely than a wider hull . The port side of the hull has next to nothing for a planning surface compared to the starboard side . It will allow that side to dig in especially with the larger planning surface on the...
  18. M

    Gph at various rpm...thoughts?

    Pretty sure you have that backwards . Your 115 is more like a 100hp figuring a 10% loss of hp between the crank and the prop . Try Googling it .
  19. M

    Stringer question

    Could be . If it was my hull and someone inspected it while second guessing his equipment , I would want a 100% , the stringers are shot from him . Me , I would then look for any clamps ,brackets etc . screwed into the stringers in the bad reading section . If nothing was in the " questionable...
  20. M

    Conversion from I/O to outboard on Islander.

    When the OP wrote Islander my first thought was a Starcraft Islander , not the glass , Grady White ? . So knee braces ,as noted above , are not used .
Top