Search results

  1. B

    Manuals for sale. Check out the link.

    Advertising for another site is not allowed here.
  2. B

    selectric to toggle conversion video.

    I converted my push button control to toggle control due to forward button starting to go out on me. I installed two toggle switches, one that is the main control and another that is a safety control for reverse. I thought it could be useful since my wife is a blond. I was very concerned...
  3. B

    push button shift/TOGGLE SWITCH UPDATE SOLVED THANKS FR

    anybody have any idea on getting this part? 1970 evinrude. My forward button doesn't stay engaged unless i keep pressure on it with my thumb. edit: I've researched and found out that there is toggle switch conversion out there. Do I just need the specific toggle switch? I have a green...
  4. B

    What is this part called?

    This donut looking bushing broke off on my starter causing the starting wheel to spin higher than the flywheel. It shows up on the parts diagram but not listed??? It is located below the lock nut #2 and wraps around the spring above the gear looking wheel.
  5. B

    1970 115 hp evinrude water pump.

    before dropping the lower unit you are suppose to disconnect the shift wires up by the powerhead. After doing that, does one have to remove the insulation wrap around the two wires leading down towards the gearcase?
  6. B

    1970 115 hp evinrude.

    now I got the ignition problem solved took this boat out and ran it the last couple weekends. Awesome power. Only problem now is the overheat light/alarm sounds. Very week and would only sound last week at full throttle...throttle down and it would quit. Today it was off and on the whole...
  7. B

    WOT Motor cavitation

    115 hp evinrude on 16 ft larson mirado. At WOT I notice my boat will increase in rpm's while not increasing in speed. Gives a feeling like motor comes out of water. After a few minutes overheat alarm will start kicking in. When I throttle down just a hair, feels like motor catches the water...
  8. B

    1970 Evinrude 115 HP PROBLEM FINALLY SOLVED.

    Well after about $700 of parts I finally solved my problem. Some of the parts were probably bad, but deep down I think I just made my motor newer. I'm posting this in case somebody else ever runs into this(probably won't be as dumb as me, but oh well) when I removed the ignition bypass switch...
  9. B

    Cdi Ignition Coil Ohms Readings PROBLEM SOLVED!!

    Took the existing CDI coil off my evinrude. Has primary lead from pulse pack and secondary lead going to distributor. My ohms reading on this one was HIGH on the primary lead to ground. On the secondary lead( to distributor) to ground read low. Checking continuity between two leads on this...
  10. B

    ignition coil resitance

    on my ignition coil which has primary lead from terminal 5/blue wire pulse pack and high tension lead to distributor. When I do a resistance test on a x1k meter these are the two readings I get. primary lead from terminal 5/blue wire pulse pack I get 2.5 ohms(x1k meter) secondary or high...
  11. B

    3 wires from remote control box

    Have a 1970 evinrude 115 hp motor that has three wires coming from remote control box. One is grey and the other two are red, red/black. I figured the grey was the tach, but what are the other two for? My manual doesn't show these three wires.
  12. B

    1970 evinrude solution. Thanks Joe reeves and FR

    After assistance from FR and Joe Reeves I've learned the proper way to test motor. I basically tested everything back***wards. The sensor wires had a ground short. Once inside the distributor and pulled wires off sensor I checked the sensor. High ohm reading stayed when adjusting throttle...
  13. B

    black/yellow kill wire 1970 evinrude 115 hp ??

    Does this exist on this motor? I see no black/yellow wire at all. Can't find anything stating kill switch in the manuel.
  14. B

    1970 Evinrude 115 HP Loses spark-gains spark etc..

    Heres the story. Bought this boat with the understanding that the previous owner had reversed battery terminal wires. 1. Took it out, ran ok except surged at high speed. 2. Thought that was fuel, changed all fuel components(cleaned carbs) 3. Boat ran fine again, except at high speed. 4...
View older results
Top