Search results

  1. Bustedknuckle84

    Can you help me identify the hydrofoil that use to be on my motor?

    I have a 200hp Honda outboard. I bought it with the holes in the lower unit and it didn't have the hydrofoil on it. Here is some of the info please help: 1)The holes are 4" apart from each other 2) The holes are about 2 inches in from the outer edge Its not the attwood hydrofoil the holes didnt...
  2. Bustedknuckle84

    Bennett trim tabs trim indicator installation question on sealing to the boat.

    I had to remove some kinda of sealant to remove the top part of the trim tabs pump from the hull of the boat. I am wondering what do i need to do to seal the top part of the trim tab to hull of the boat?
  3. Bustedknuckle84

    MIL-PRF-5606H HYDRAULIC FLUID, can it be used on multiple componets?

    I purchased this fluid thanks to some help from a iboat forum member for my hydraulic steering unit. 1)Im wondering will this fluid also be compatible for the bennett trim tabs hydraulic unit? 2)Also Can I use this on my Honda power trim unit? Trying to save space so if the MIL-PRF-5606H...
  4. Bustedknuckle84

    Teleflex seastar outboard hydraulic steering question

    I have this system on a 200hp honda motor. I am wondering what fluid can I use to top off the Helm's steering Reservoir for my hydraulic steering? Do i have to get Teleflex's hydraulic steering fluid? What do you guys use for these sea star systems?
  5. Bustedknuckle84

    Researching but can't find an answer on prop diameter

    I used the prop wizard from turning point and inputed all of my boats data however its showing me a 14 1/4 diameter other website are showing the same. I just bought my 22.5 ft center console in the signature a month ago. It came with a 15 1/4 diameter SS prop from honda. But I dont think its...
  6. Bustedknuckle84

    lower unit refilling procedure question

    If you (pump) fill the lower unit oil from the top instead of bottom, do you have to drain and refill from the bottom to the top.Or as long as it pores out from the top I will be good? I don't have a manual yet but heard you have to do it from the bottom.
  7. Bustedknuckle84

    How do you drop the lower unit on a bf200?

    I am still getting a random noise on the lower unit, scared to take my boat out. Want to drop the lower unit and inspect. Do you keep it in gear when dropping the lower unit? Heres a link to my lower unit noise. http://youtu.be/la-n-307l98
  8. Bustedknuckle84

    Can you help identify this electronic piece think its a fuse

    I have a picture of a believe to be fuse because it says 20a on it. it has 2 electrical + connections one coming in from source and and one going out to the switches. 1) What is it? 2) Is it necessary to have it? Im going to use a distribution block with fuses..
  9. Bustedknuckle84

    Racor fuel/water separator filter with clear bowl question

    I bought my 02 cape craft about a month ago, its in the signature. However it came with a racor fuel/water separator. Looks really old or never changed. I believe the gas is old as well, but i put sta-bil in it recently. I tried emptying fuel/water seperator due to that bottom bowl being...
  10. Bustedknuckle84

    strange electrical issues lowrance is reading 6volts

    I have some wiring issues, My lowrance downscan unit reads 6volts and barely turns on when my boat key is not in the on position. However, I confirmed that the +and - wire connections from the unit are getting 12 volts even down to the power source. However when the key is in the on position the...
  11. Bustedknuckle84

    Please help..Lower unit noise on my 2003 BF200 hp 4 stroke FI

    The lower unit has the following noise in this youtube video. Only makes this noise in gear, what could it be. Prop was loose but i tightened it down good. Still have the same noise. I forgot to put the motor up and drove the boat on trailer when the motor was down and it did scrap the concrete...
  12. Bustedknuckle84

    Is this light suppose to stay on? looks like the battery light.

    After i turn the key to the run position all lights come on i hear two beeps then this one light stays on. what does it mean. I have an 2003 Honda 4 stroke fuel injected 200 hp motor.
  13. Bustedknuckle84

    doing a rewiring project need help identifying

    This resistor looking wire is connecting the nav lights switch. to the bilge switch i believe. What si it for and do i need it?
  14. Bustedknuckle84

    Rpms exceeding 3k ok to do out of water hooked up to water source though?

    I have a 03 Honda 200 HP 4 stroke fuel injected. Is it ok to run the rpms to the highest point for a second or 2? Will the rpms go up to max when out of the water (of coarse with water hooked up) or is there a safety measure limiting to 3k and below. Seems like my rpms do not go above 3k.
  15. Bustedknuckle84

    Can you custom make a t-top canvas?

    I see you can buy the fabric, but is there a kit that will punch the grommets through the fabric to lace the t-top canvas to the t-top frame?
  16. Bustedknuckle84

    WOT when outboard is not on the water ok?

    I have a 03 Honda 200 HP 4 stroke fuel injected. Is it ok to run the rpms to the highest point for a second or 2? Will the rpms go up to max when out of the water (of coarse with water hooked up) or is there a safety measure limiting to 3k and below. Seems like my rpms do not go above 3k.
  17. Bustedknuckle84

    Will a #8 anchor hold a 23 ft cape craft down?

    Simple question but the sales person didnt know.
  18. Bustedknuckle84

    Strange tachometer readings please help.

    I bought a cape craft with a 03 honda 200 hp outboard. The rpms gauge (tach) is acting wierd. with motor off the gauge is reading 1k or less constantly. with the key turned but not started the tach will move to 0rpms. then with motor on the rpm gauge will not go past 2k however when returning to...
  19. Bustedknuckle84

    How to use ohm meter on fuel sender

    I read a bunch on what the ohm meter should read when testing the fuel sender, however how do i use my multimeter to test the ohms. Ex: i tried connecting the negative to the negative on the sender, and positive to the positive on the multimeter. it shows a constant 14ohms regardless of the fuel...
  20. Bustedknuckle84

    Tachometer problems on 03 honda 200 hp outboard

    I bought a cape craft with a 03 honda 200 hp outboard. The rpms gauge (tach) is acting wierd. with motor off the gauge is reading 1k or less constantly. with the key turned but not started the tach will move to 0rpms. then with motor on the rpm gauge will not go past 2k however when returning to...
Top