Search results

  1. J

    chrysler parts

    is there a place where you can get parts for chrysler motors from like the chrysler corporation? Or do you have to go strictly from individual dealers? I have a Johnson motor as well and I can just log on to evinrudes web site and order straight from there...is there anything somewhat the same...
  2. J

    reinstalling carb on johnson 9.5

    I was wondering if when I am reinstalling my carb on a 1971 johnson 9.5 and I am tightening down the little thing that springs and controlls the throttle, Do I just make sure the throttle from the tiller is in the slow position (all the way pulled back) and then make sure that little thing that...
  3. J

    fuel pump for johnson 9.5

    I just reassemble my fuel pump and I was doing the blow test. I can blow in the input valve but not just totally freely. I have to give a bit of effort. Not a ridiculous amount, but a little. My question is that I can also blow really hard and air will go through the output valve. Only if I...
  4. J

    9.5 johnson carb kit

    just got this thing and there are a couple of parts I dont recall seeing included in the kit when I disassembled my carb. There is a round screen that has like 3 small holes on it other than the hole right in the middle, a bigger round cork gasket looking thing, and a small cork oring or...
  5. J

    best product / method to clean carb on johnson 9.5

    I just took my carb off and have it broke down. Before I put it back together I was going to ask what is the best method and product you guys think to get it really clean. Do I need to soak? I was wanting to spray, soak, and then air dry with canned air. What do you guys recommend to do it...
  6. J

    1971 johnson 9.5 carb problems

    Ok I ran the motor this past weekend and on the topend it doesnt perform well at all. It idles fine, but when ran open, it bogs down and rpms just sound like they arent as high as they need to be. I am sure it is a carb problem. I am going to run some sea foam through the gas tank as well as...
  7. J

    1971 Johnson 9.5 Fuel Pump question

    Hey all, I took apart my fuel pump and reassembled it, but I left 1 piece out somewhere. Its just a small circle plastic piece about the size of the end of your pinky finger. maybe even a bit smaller. do any of yall know where this goes? I would appreciate any help. I would assume it goes...
  8. J

    1971 johnson blues - Update

    Ok i got the motor in the water (trash can) today with fresh seals on the lower unit, new impeller, and a new starter pinion. ready to test it out. started up after a few pulls and ran a little rough, but it finally warmed up and started sounding better but i ran into a problem. it runs fine...
  9. J

    1971 johnson 9.5 starter recoil replacement

    Ok, when I bought my 9.5 earlier this month used, it had a worn out starter pinion (the plastic sleeve with gears). I am having a bit of a problem after replacing this part. Here are the steps i took. 1. slid new pinion over recoil shaft 2. tied rope to recoil and pulled rope all the way out...
  10. J

    johnson 9.5 lower unit q's

    ok, this was actually my first experience working on an outboard myself. i have a 1971 johnson 9.5. i bought a new impeller and lower unit seal kit due to water being in the lower unit oil. i replaced the o ring on the propeller, the spaghetti seal around the bottom, the nylon washers on...
  11. J

    got motor today (1971 9.5 Johnson)

    Ok got the used motor today and this is what I found. Needs a new starter pinion as I mentioned earlier. It seems to be in decent shape, but I have a couple questions. Take in mind I have a repair manual on the way because I plan on doing all the repairs that I am capable of doing. 1. Lower...
  12. J

    1968 chrysler 6.6

    anyone know where parts can be found for this motor? I am talking just the normal routine parts. Impeller, maybe carb kit, seals, etc... thanks
  13. J

    johnson 9.5 outboard

    I know they only made these in the late 60's and early 70's. Couple of questions: 1. are parts still easy to come by new. if so where? 2. i have a part that is worn out on mine that I dont know what its called or where I can get it. Its the gear by the pull string that is plastic. its...
View older results
Top