Search results

  1. Lyndy

    OMC Stringer Anode Replacement

    Below are two Anodes. The first is the Transom Anode and I saw no doubt that it needed to be replaced. I did so with an OMC Replacement. Thanks Ebay! The second one I am not too certain about. The part is mounted directly to the underside of the Intermediate Casing, does not have any Errosion...
  2. Lyndy

    OMC Stringer Bronze Tilt Gear

    Preparing a number of parts for painting. The tilt gear is completely corroded. Is there a solvent I can stick the gear in to clean it up or am I faced with replacing it or trying to clean it by hand?
  3. Lyndy

    Ball Gear Wearing Poll

    The picture below is on Ebay claiming 80% life left on Gear (20% Wear?). I asked sometime back what wear looks like so I could judge the gear on my Intermediate casing. Mine does not appear to be as worn. I would like to know from everyone what kind of percentage wear this gear has?
  4. Lyndy

    I.D. Info found on Intermediate Casing

    While stripping paint from my Intermediate Casing, I found the following Information on the top of the casing near the filler plug: 2205A There was the letter "G" couple of inches to the left of this number. Any clues as to what this number may represent?
  5. Lyndy

    75-76 OMC Drive Exhaust Seal

    There is a seal on the Upper Gear Case that I am not sure what to look for in regards tp wear. It is a Hard seal with a spring inside it where the Exhaust Port on the Itermediate Casing mates with the Drive when it is in the down position. Any guidance in determining whether it should be replaced?
  6. Lyndy

    OMC Stringer Exhaust Housing Seal

    While on my refurbing campaign, I also want to replace the seal on the Exhaust Housing that the Upper Gear Case sits on since it is showing some cracks. I have found the seal on the internet but have had no luck in finding a kit that includes the seal. Does it come in a kit or am I going to have...
  7. Lyndy

    Replacement Parts for OMC Drive

    As I continue working on this '74 Skipjack, I am gathering information on possible parts that I will want and need. While on my quest, I see there are a few After Market sources. Bomadier, Sierra, GLM and of coarse Original OMC. I suspect there are more, but these are the ones I see the most...
  8. Lyndy

    Sand Blasting

    I am preparing to paint my Outdrive/Intermediate Casing and various smaller parts. Am considering using a "Mini" Sandblaster that uses Propellent. Are there better ways to do this?
  9. Lyndy

    OMC SternDrive Pivot Cap Cover

    Although I do know what this part is called, I can not match it up with any drawing in all the manuals I have and BRP site. The Boat it came off is a 1974 Skipjack. The original motor has been replaced some time back so there is no Model number to refer to. The current Engine is a 96-98 Chevy...
  10. Lyndy

    Upper Gear case Marking

    I saw this marking on the Upper Gear Case when I removed the outdrive this weekend: Upper Case 21 17 Any comments on this to help me Identify this outdrive?
  11. Lyndy

    Pivot Cap High Profile Stringer

    Removed my outdrive this weekend and took a number of pictures. When I returned home I started looking through the number of Manuals I have collected and noticed something I could not find in the parts catalogue or pictured in the manuals but on my outdrive. There are a several pictures of the...
  12. Lyndy

    OMC Upper Gear Case ID Model 980064

    I have been looking through all my parts manuals and Online with no listing for this number. I expected it to be a Upper Gear Case Assembly. Does anyone have this number listed anywhere?
  13. Lyndy

    OMC Stringer SternDrive Compatibility

    I have a 74 High Profile Stringer Outdrive mounted to a 5.0 Chevy 2bbl Rochester Carb. I have an oppurtunity to pick up a 73 225 HP High Profile Stringer Drive that is presently mounted to a 5.7 Chevy. My present Drive is probably not a 225 HP, probably 190HP. Any performance or compatibility...
  14. Lyndy

    OMC Outdrive Older Stringer ID

    I have gone through a fair amount of this Forum, along with 2 other popular forums and questions about ID'ing the older Stringer Drives seem to go unaswered. I thought I will try a slightly different question here. Did OMC Mark their earlier drives with a serial number or model number? 1974 24'...
View older results
Top