Search results

  1. D

    testing 1986 evinrude rectifier

    need to check rectifier , new stator need to know out put of rectifier. yellow wires are ac, red dc? what are the voltages. think this is problem tach out.
  2. D

    this is getting old

    1986 evinrude 140 alarm didnt work on vro failer, all is well however, pulled alarm totally toast. any way to find a repalacement or use a light on the dash to replace this has a two connnector and all the temp and vro sensors have no resistance what would case the the alarm to cook.HELLLPPP
  3. D

    output on rectifier

    have a 1986 140 evinrude, I have a clmers manual but is not helping Whats the voltage from the requlator on the red wire to ground(dc) and the yellow wires fron stator, its a brand new stator, possibly defective? also new power pack, have done output tests Im only getting 12.45 volts at red and...
  4. D

    chaging older(1986) motor to synthtic oil

    considering changing to pennzoil 100 % synthetic oil is there problems relating to to this oil removing to may deposits
  5. D

    checking voltage from charge coil

    1986 evinrude 140 h.p. trying to determine charge coil output. I'm using a ac meter on the two leads, get 86.5 volts, should this be multiplyed by 1.414 to obtain voltage reading of a cd volt meter, I understand the 175 volts required. What is the differance between a digital multimeter and a cd...
  6. D

    1986 evinrude 140

    looking for jet sizes for carbs. model e140tlcdc, serial#g1134300. thanks in advance for any help
  7. D

    1986 evinrude won't go over 2400rpms

    rebuilt carbs, new vro, new power pack, resistance in stator and charge coil ok, 12.82 volts to batteries. can I check voltage to power pack with a digital volt meter and should it read 175volts running or just cranking. doess this motor have reed valves?? or the slow circuit. If I dissconnect...
  8. D

    engine cuts out at 2400rpm

    carbs have been rebuilt,new vro pump, fuel system all redone, checked stator, coils charge coil. when the engine overheated a month ago the rpms dropped down to 2400, I believe this is the s.l.o.w. system working. Repaired overheating problem, now the engine won't run over 2400. iis there a...
  9. D

    wiring new vro

    installed new vro pump, had a three wire connector black,gray,brown. new has purple wire as well, does this go to purple in the power pack :confused: thanks in advance
  10. D

    starter wont spin fast

    just replaced head gaskets, spun the motor, plugs out to get compression reading on all 4 cyl. checked 2 cyl nothing for the nexted. motor spins but not enough to engage bendix. checked voltage at motor when solenoid is engaged reading only 6.4 volts. check power to batteries when starter is...
  11. D

    misfiring 1986 140 evinrude

    long story try to make short, vro failed. temp sensors limited the engine to about 2200 rpm. stopped engine. replaced vro and engine starts.idles. misfiring just above idle as it tries to plan out,then starts to stall.pulled plugs shecked compression. 1 cyl not firing plug was like new conditon...
  12. D

    1975 9.9 evinrude

    problems with shifting, once in gear cannot get back in netural. cannot get back to netural to start. any ideas
  13. D

    part# for vro pump

    need to confirm part # for 1986 140 evinrude was told it was a 05004559 or the 50:1 version 0398399<br />thanks
  14. D

    plywood veneers

    I'm looking for thin mahogny veneer to resurface top side and repaired transom on a 1957 higgins supersport 17' any links would really help. thanks
  15. D

    primer solenoid for 140 evinrude

    I have a 1986 140hp evinrude.It has a primer solenoid mounted on the air silencer. It also has a red pointer(up or down) mounted on the solenoid. I've check my manual and it doesn't mention the pointer, I'm Assuming its a manual lever. What position should the pointer be going for normal operation.
  16. D

    vro pump

    looking for contacts for a new or rebuilt vro pump for a 1985 140hp evinrude
View older results
Top