Search results

  1. R

    Johnson 150 V6 Ocean Runner - not starting

    Thank you Sir.
  2. R

    Johnson 150 V6 Ocean Runner - not starting

    Lets say it was the powerpack that needed replacing (if no good spark is present) is that fair assumption?
  3. R

    Johnson 150 V6 Ocean Runner - not starting

    Thank you. I did use a wire brush on plugs, but the wiring bundle near back of engine, appears to have significant corrosion so I suspect all of it to be original wiring - 1993 (like the starter was). So likely that I do have a poor ignition system (low spark which is highly likely). Batteries...
  4. R

    Johnson 150 V6 Ocean Runner - not starting

    Thank you. Do you know if there are specific cylinders it disables electric on the coil from?
  5. R

    Johnson 150 V6 Ocean Runner - not starting

    Also, original wiring from 1993 does not look to be 100%…pretty sure one of the overheat sensors isn’t wired right.
  6. R

    Johnson 150 V6 Ocean Runner - not starting

    I was able to get a spark with the NGK plugs. I only tested two of the six cylinders on one bank. The spark seemed weak to me, but it was present.
  7. R

    Johnson 150 V6 Ocean Runner - not starting

    This is all i have left on the model # tag
  8. R

    Johnson 150 V6 Ocean Runner - not starting

    1993 Johnson 150 V6 Ocean Runner 60 degree
  9. R

    Johnson 150 V6 Ocean Runner - not starting

    Rebuilt the carbs, new plugs, and starter. Was running for a month and then no more. Heavy black deposits on NGK plugs I had in there....went and bought new Champion spark plugs (per another iboats thread) and they wont even generate a spark when I test them. The NGK's still generate a spark...
  10. R

    Johnson 150 v6 - fuel pump location

    Awesome thank you.
  11. R

    Johnson 150 v6 - fuel pump location

    The VRO pump was disconnected prior to me purchasing the boat. I was hearing a clicking noise at the VRO and disconnected that power harness to the VRO pump. Question is - does the fuel pump require any electricity from the VRO pump wiring harness, or is it a simple diaphragm assembly? Seeing...
  12. R

    Johnson 150 v6 leaking gas at idle

    Thank you
  13. R

    Johnson 150 v6 leaking gas at idle

    But what are the carb bolt torque specs on Johnson 150 v6 1993?
  14. R

    Johnson 150 v6 leaking gas at idle

    Thanks for all the replies - found some leaking carbs and picked up gasket kits (to arrive today). Anyone know the Johnson 150 V6 carburetor bolt torque specs?
  15. R

    Johnson 150 v6 leaking gas at idle

    Yes it really does sound like a BAD idea. Carbs are warped, does the rebuild kit come with the plastic sides and gasket. Would you mind pointing me to part # or link? This caught my "fix it quick" eye "Permatex MotoSeal 1 Ultimate Gasket Maker" For two and four cycle engines. Solvent-based...
  16. R

    Johnson 150 v6 leaking gas at idle

    I replaced all line fuel fittings (was zip ties) with stainless hose clamps. Snugged carb bolts. Still leaking from side of carb - warped is the plastic cover and brown gasket. Second issue of lower unit - thank you forgot about prop seals etc. Its been 10 years since my last johnson and boat...
  17. R

    Johnson 150 v6 leaking gas at idle

    My apologies - year 1993 Johnson 150 v6
  18. R

    Johnson 150 v6 leaking gas at idle

    I have checked a few videos online, so appears to be something the pump, lines, carbs, or vapor separator. Also, changed the lower unit and found grey oil (so water in it). I have changed that lower unit oil out, and fingers crossed that it wont be gray again. If it is - would love advice on...
  19. R

    Johnson 1998 VRO clicking

    my Johnson 1998 50 spl is leaking at the bottom through a hose and clicking alot. Do these units click from flow problems due to bad hoses? I appears that I was getting too much oil as it was coming out of the exaust and dripping out from under the vro.
  20. R

    Tilt & Trim leak

    I have a 1998 Johnson Tilt & Trim that is leaking from the top where the rod goes in. I picked up the o-ring kit and replaced o-ring, but still leaks. I am confident that I dont know which washers are used for the piston entry point. I looked at the exploded diagram on Johnson's web site I am...
Top