Search results

  1. M

    What the heck is this hole?

    Well this is probably a really stupid question and it shows how much of a rookie I am. But I recently lifted my motor and I was inspecting the bottom of the hull on the boat, when I noticed a hole about 2/3 of the way up the boat on the port side, it is definitely there on purpose does it have...
  2. M

    hole shot problem

    I am having a problem with my boat on take off. If I go to full throttle, the boat bogs down, throws the nose way in the air and then does what I call over revs or maybe cavitates. If I throttle up slow at first and then hammer it it pops out just fine. It is a 91,90horse Johnson on a 16 foot...
  3. M

    Which Stainless Steel Prop

    Well thanks to Kenny aka Walleyehead Ive figured out which pitch prop and I know for sure I want to go stainless, but which one I was told to shy away from MW Rapture because of the cup, I have 90 horse johnson that needs to get the RPMs up so Im going down to a 15 pitch, that is why I told not...
  4. M

    Changing Carb Jets!

    I recently got my new to me boat out and ran around the lake. It is a 90 horse 1991 Johnson. It has really low hours for a 15 year old motor but it is only putting out 5050 RPMs and I have been told that it should be around 5700+ Im running it at 4800' in elevation Im thinking it has the...
  5. M

    Finally got the info!

    Well we had some water open up here in Montana(really strange for Feb 9) so I fially go my new boat out 16foot Lund Tyee II with a 1991 90 horse Johnson with very low hours (does have a fin on it), well new to me anyway. So Im looking for some prop ideas. The current prop is 13 1/4X17 and I...
  6. M

    oil leaking from prop

    I went out to the shop today and I noticed and oil/grease leak out of my prop running down my skeg my motor as been in the down position this winter in the shop but it still has gotten well below zero here. It isnt alot of oil maybe 3 or 4 ounces. Any ideas, also right at the end of the...
  7. M

    Minn Kota shaft lengthening question

    Wondering if anybody on here has ever replaced a shaft on a Minn Kota Maxxum, the current shaft is only 42" I want to change the shaft out to a a longer shaft and am wondering if any of you guys have done this before.<br />Thanks <br />Jamie
  8. M

    1991 Johnson 90horse VRO2 system.

    My question on the oil injection system for this motor is, how do I know what mix the system is running, in the manual it says that during breakin and "high performance" operation that it should be run at 50:1, I just inherited this boat and it has less than 50 hours of operation, I know from...
  9. M

    91 Johnson 90 horse carb question

    We were just foggin and cleaning up the motor on my boat when we noticed that a part was cracked and spitting fuel. Im no mechanic but I will try and explain where this part is, if you are looking from the prop side of the motor it is on the top right side of the carbs, it is a red plastic...
  10. M

    Prop for 1991 90horse Johnson

    Looking for a little help in prop selection for my 1991 90horsepower Johnson, Im more interested in performance and durability than price. Thanks a bunch for the help?<br />Jamie
  11. M

    1990 90 horse sleeping Johnson ?

    I recently picked up a Lund 1990 Tyee II with a 90horse johnson on it. I am wondering how to drain the old fuel from the tank and engine. Also any other things I need to do to this setup after it has sat so long, 6 years, I will definitely replace all the lower unit goodies, impeller ect...
View older results
Top