Search results

  1. L

    Battery kill switch.

    My boat is fitted with Ford V6 3LTR Marinised engine with alternator, I would like to fit battery kill switch, I have a standard on/off kill switch and considering the alternator etc, would like to know where to fit it and in which line ie positive or negative? thanks for any advise/...
  2. L

    Tachometer with electronic ignition fitted?

    Does anyone know if a standard car type tachometer will still work when the points set-up is removed from distributor and electronic ignition module fitted, my engine is a Ford Essex V6 marinised unit. many thanks. JD:confused:
  3. L

    single on/off switch or on/off/on?

    I have fitted another bilge pump, now have two. Should I wire them to 2 seperate on/off switches with their own wiring and fuses or could I wire them on one on/off/on switch? Like switch up = pump no 1 running, middle position= Off, down position = 2 pumps running, I can wire it so pump no 1...
  4. L

    ignition light when switching on to start!

    Can anyone please tell me where to wire ignition light to/from so that I get red light when switching on key? Inboard petrol engine set-up
  5. L

    Charging light circuit wiring.

    My inboard engine is a Ford Marinised V6 Essex pertol, several wires loose on dash panel, the small light which should show if engine is charging needs connecting, where should it be wired to? engine has altenator, Many thanks Lurcher.:confused:
  6. L

    OMC Tachometer

    Can anyone please tell me if my OMC Tacho will operate on a petrol marinised V6 Ford engine the Tacho can be switched and is marked on rear with 1 to 6 pulses per rev! would it get the signal from Distributor? Many thanks Lurcher:)
  7. L

    Use of OMC Tacho on petrol engine?

    I have a nice working genuine OMC Tacho which I use on my Evinrude 40hp, it has positions on back to select number of cylinders on engine, however I now own an inboard engine which is a Ford V6 petrol and wonder if the Tacho would read? thanks JBD:confused:
  8. L

    How to see previous postings?

    I was given information on previous postings and wonder if I can go back to them? Have trawled around but cant find anything! Thanks Guys Lurcher.
  9. L

    Tachometer installed.

    My BE40ELCR and OMC control box. I purchased original OMC Tacho and with advise from here connected it and ran engine yesterday, Tacho has original loom with plug in to control box, 2 prongs inside, question is this,:D Tacho runs only when I hold the end of plug at certain angles (bad...
  10. L

    OMC Tachometer and Evinrude 40hp.

    My engine is a Evinrude BE40ELCR 1984, I have an OMC Tachometer details are,Aqua meter inst.corp. Roseland N.J. U.S.A. 07068 on back is pulse switch,(pulses per rev) reads from 1 to 6, with details, Set Pulse Switch as Engine Requires. Grey Wire To Pulse Source. Black Wire To Ground. Has wiring...
  11. L

    Seasons Greetings to all.

    Best wishes to everyone on this excellent web site, good health for 2008, from Lurcher Bonnie Scotland.:D
  12. L

    Evinrude 40hp BE40ELCR

    My engine has 11/3/4 by 17, it puts my 14ft speedboat on plane in seconds but runs out about 32mph on GPS, would a change of pitch help top speed or leave alone? Lurcher.
  13. L

    Yamaha Tacho!

    I have Yamaha Tachometer reads on dial Nippon Seike Japan, and scale up to 8,000rpm, on back is only 2 wires green wire and black wire? was on boat I purchased, I this likely to work on say Evinrude/Johnson outboards (I know my Evinrude Tacho can be switched to select amount of cylinders)? thank...
  14. L

    Faria water pressure gauge.

    Decided to replace my instruments with new white Faria and include water pressure to fill up hole, this gauge comes with threaded adapter that screws into hole in cylinder head, my engine is Evinrude 40 hp BE40ELCR which I dont think has this tapping, can I use T piece inside engine cowling on...
  15. L

    Johnson 40hp 40R746

    Purchased this engine couple weeks ago from untruthfull gentelman on an auction site? was sold as running engine in good order which had just had head gasket replaced, it arrived seized, took several hours with 2 stroke oil/ WD40 moving it 1 tooth at a time on flywheel, I freed it off but it...
  16. L

    Back on iboats after nearly 1 year!

    Amazed this morning, have just found iboats again after most people here in UK were denied access, I am AOL Broadband and lost it nearly 1 year ago, many people from several countries could not get on either, there were web sites to discuss why it could not be accessed, anyway I am pleased to be...
Top