Search results

  1. E

    Peanut Butter PB mess

    My peanut butter repairs are for two purposes. Leveling out the hatches as they had dished in void areas around the plywood stiffeners (these recesses are as much as 1/2 inch deep). Filling holes in hatches as I plan to change from top hinge to piano hinge and holes around the cap to hull at the...
  2. E

    1984 warning horn melted New part fit? Wiring ?

    0585992 is the original part number what new part numbers will fit? The old one was just round with tab coming off the side for the screw. The new ones look like they have wires attached while the old one just had tabs for flag connector. Voltage at the purple and tan wire was 2.8 volts and I...
  3. E

    E100WTLCRS 84 100hp tach dropping out during throttle up

    About to my wits end. Just got back from lake to try my latest repair(new coil). Spark gap tester now showed(haven't checked again since I got home) good 7/16 spark on all cylinders. During throttle up (attempt to plane off) the tach is dropping out and as soon as I pull back on throttle the...
  4. E

    Carb rebuild mistakes on 1984 100 HP (typical v4 crossflow)

    What are some of the common mistakes us rookies might make during carb rebuild. I installed two new kits and all new jets after checking old ones with pin gages and found them oversized. Removed the core with drilled hole and awl and everything was spotless cleaned before re-assembly. Float open...
  5. E

    1984 100 hp evinrude e100wtlcrs retorquing heads

    Water is dripping from (hard to see while floating at the lake) starboard lower cylinder head area. It is dripping on the new cylinder head hose area. I have retorqued the heads once after break-in (book says 18-20 ft lbs.) Is it sometimes needed to tightened up to a higher torque? Say 22 or 25...
  6. E

    E100 WTLCRS no spark one cylinder

    During the break in period of my recent rebuild above 3000 rpm it would be running along fine then "hiccup" for just a second then go back to running fine. It would only do this like every 10-20minutes or so. I thought bad gas. Well the "hiccup" got worse and i do not think it is gas any longer...
  7. E

    Power Pack black/yellow wire 84 100 hp E100WTLCRS

    Guys, When people mention disconnecting the black/yellow wire at the powerpack does this mean using pin removal tool to pull pin out of Amphenol connector? Or removing the wire at the terminal strip? Just trying to learn where for reference. I think my kill system is fine.
  8. E

    XP 1987 100 hp

    What does the XP mean? What was different in these models? Just looking at outboard and I don't have access to model number.
  9. E

    Spark Lever Advance Sticker 84 100hp E100WTLCRS

    I got some carb cleaner on the little sticker on the spark advance lever that shows the timing max advance and you can't read the number. Does anyone know what the correct number is or where to get a replacement this sticker?
  10. E

    Spark Gap Tester and Joe Reeves method and backfire 84 100hp

    Guys, I have a question about Joe Reeves timing method. Why do you need to hook up a spark gap tester to set the timing? My 84 100hp that I have just finished the 10 hr. break in on my 1st rebuild but there is a backfire (I think) every 20 minutes or so above 3200 rpm so I think I have a...
  11. E

    Stuffing wiring V4 100hp crossflow

    Guys, On the port side of V4 you have tilt/trim wire harness, Battery wires, main wiring harness, fuel lines. This seems like trying to stuff a turkey. What order should these be in? E100WRLCRS 100 hp. And is it really crowded around the red plug? Thanks, Ed
  12. E

    V4 Link&sync crossflow 84 100hp

    I have OMC service manual however I think I saw on here a Joe Reeves Link & Sync method. I have looked for 45 minutes on here but can't find it. Did I imagine it or can someone show me the post. Thanks, Ed E100WTLCRS
  13. E

    Temp Sensor Vacuum Sensor wiring 84 crossflow 100hp

    The vacuum switch has one lead that goes to ground. The other lead goes to an insulated lug on the bracket. The wiring has twin tan (labeled V) wires with a ring terminal that goes to this insulated lug. The wiring diagram shows one tan wire on the boat side wiring harness and 3 tan wires on...
  14. E

    V4 rebuild 84 crossflow 100hp Photos of old parts

    1st warm weekend was in Feb. and that is when I tore into my 1984 Evinrude 100hp. Here are some photos of old parts including sparkplugs that look like two new and two old but that is how they came out of block. 3 of the pistons look coked up but no wear. One is toast, well you can see what it...
  15. E

    photos of powerhead rebuild crossflow v4

    Still working on getting mine back together but I bet some of you are very proud of you powerhead rebuild work and would like to post photos. Plus a photo is worth a thousand words. Here are a couple of before photos. Evinrude V4 crossflow 1984 100hp.
  16. E

    Spark Plugs Gapless

    Looking for advice suggestions on why or why not go with gapless sparkplugs. Champion L77J4 or QL78V or L78V or QL16V are listed for 84 100hp being eventually remounted on 15-1/2 foot bass boat.
  17. E

    OMC Evinrude reed plate part number?

    Can someone tell me the part number for just the reed? 100 hp E100WTLCRS 1984 v4. Not the reed assembly. Found it sorry 317739. I don't know how to delete a post.
  18. E

    Recirculation Tee Install

    I am open to suggestions for installing 1/16 BRP 326449 hose onto 5 way barbed fitting 329688 that I now have to replace. OPPS.:eek: I tried both windex and isopropyl alcohol as lube but I guess PB blast would have worked better. Has anyone seen these 5-way barbed tees from brass? I have see...
  19. E

    Throttle Play V4 84 100hp

    Guys, I have all the parts in throttle cleaned and lightly triple guard greased. See attached diagram item numbers 76 and 82. These seem loose side to side after installing the washer and lock nut. Is this last washer supposed to fit up over the shoulder? I would think this assembly would be...
  20. E

    Evinrude 309924 bolt length

    Can someone confirm for me the bolt length of 309924 bolt for lower crank bearing to crankcase not the one for the bearing plate? This is 1/4-20 x 7/8 hex with star washer I think?
Top