Search results

  1. Charlie61

    1983 115 inline mer, runing

    hello again just got motor running after replacing almost all electrice parts . starts normal, can put it in grear still runs normal. When I go to throttle up it dies . So I throttle very slow and let it run there about 30 sec. the rpm will go up. I keep doing this untill I get in to a higher...
  2. Charlie61

    lower unit seal 2

    Just replaced lowers seals in 1983 115hp inline 6 after getting help from the post. After many helpfull threads the innies in and the outties out worked . Tested it today in water and ran 10 min no oil . Thank for your help
  3. Charlie61

    1983 enrichment vale

    I have been asking for help with a 1983 enrichment vale the replacement vale it not the same at the 1983 vale the old one can be ajusted to let a small amount of fuel run thru the new one is not ajustable. this is the 3nd time I have asked. If I as not asking the right question or something...
  4. Charlie61

    Lower seal

    Sorry but I have read and have service manual but can not understand how to install lower unit seal when I remove the old seals the inner seal was going the same way as the outter seal . I saying that the lips that gose around the shaft are faceing the same way. in the manual one going one way...
  5. Charlie61

    boat size

    I have a 1971 Sea Ray 21ft lg will a mercuriser 2.5 lite work in it I got this boat after it had been redone oiutside and top hope the 2.5 will work????
  6. Charlie61

    Mercury enricher vale 2

    Put new enrichen vale on , it has no ajustment no it. is now engine runs hi RPM .try to ajust cards, no help. guess I have to time it over again. I don't want a short cut but is there a better way an the book, I;m by myself and it's alittle hard to do. 2= What do I do about the new enricher vale...
  7. Charlie61

    Mercrury enricher vale

    Hi again it a 1983 115hp inline , hi rpm last time out motor would not start. repaired staor, trigger, rec, new plugs and changed switch boxs about 4 month ago. motor had not run in 8 years , forget I rebuild carbs and water pump did all this before it would run. will after hi rpm motor would...
  8. Charlie61

    water small hole

    I got a 1983 astorgrass 17a it's 17.5 long last time out the motor stop so I was changing battiers for troling motor trying to get back to ramp then i pulled one out I saw about a 1/8 inch hi by 64th wide water " could not see a hole" comming from where the battier was setting it's fiberglass...
  9. Charlie61

    lower gears

    Hi first time motor ran in 8 years I put new stator,trigger, switch boxs, motor running great. Run about mile or so stop fished. wanted to move. running great slower down to take vido of motor working to send to wife. was running slow gave it some gas and it started up then on power, motor...
  10. Charlie61

    Z-9000

    Need help geting a use'r manual for a Eagle Z-9000 fish finder aready nbeen to there web will try calling this week also could use temp/ trand thanks Charlie
  11. Charlie61

    Helo again switchs

    Hi Well nothing works ligths, pumps,runing ligths. I have a 1983 astroglass 17.5 boat and the wiring is totaled. I have 4 switchs can only read. Ican only read one switch on right side but the lights do not can someone please tell me the other if you can One's again thanks for all the great...
  12. Charlie61

    What is this?

    thank for all of the hepl I'am getting need to know what this part is it's the copper looking thing it's a 1983 mercury 115hp inline 6 thank's
  13. Charlie61

    mercury kill switch

    Hi I have a 115 hp 1983 inline 6 please tell me where the mercury or kill switch is on or near engine I know the wiring but still canot find the switch? thank
Top