Search results

  1. reiddo1

    1986 20hp Johnson long shaft low compression

    Just freed a new to me weather seized 1986 20 hp Johnson long shaft and ran it at elevated idle with a concentrated mixture of Seafoam. While idling has improved with running, I am getting only 60 psi compression on both cylinders and 120 psi if I pour a teaspoon of oil in each cylinder. The...
  2. reiddo1

    1977 Evinrude model35753c electrical schematic

    Just purchased the subject 35 hp 1977 Evinrude long shaft. Previous owner bought it from a guy who claims it lost spark for no apparent reason and then this guy cuts and splices in wires connecting the coils, power pack and stator assembly. I am quite suspect of the wiring and am looking for an...
  3. reiddo1

    J150VCXSSS and E200TXEDR Lower unit driveshafts

    I recently bought a used 1996 200 hp Evinrude lower unit from a E200txedr and was hoping it would be a direct swap with my 2000 Johnson 150 hp counter rotating. I am trying to make a change since prop selection for the counter rotating is limited. All looks the same except the shift rod and...
  4. reiddo1

    1996 Evinrude 200 hp 25 inch leg and 2000 Johnson 150 hp 25 inch leg

    Will a 1996 Evinrude 200 hp with a 25 inch leg clockwise rotation bolt up directly to a 2000 Johnson 150 hp with a 25 inch leg and counterclockwise rotation. All replies are appreciated?
  5. reiddo1

    2000 Johnson 150hp Oceanpro Prop Slip

    I have a prop (part number 390821) on my 2000 Johnson Oceanpro 150 hp engine. This prop is a counter clockwise rotating one. My calculated slip is close to 30% using the tachometer and GPS speed over ground information. I have called Solas, gave them the prop part number from the hub and they...
  6. reiddo1

    2000 Johnson 150 Oceanpro on a Glastron Sea Fury v216

    Largely because of what I have read on this site, l am led to believe that I have excessive prop slip. My WOT engine speed is 5200 RPM and my GPS boat speed is 36 miles per hour. The engine is in excellent mechanical condition and according to Solas the 14.5 by 19 pitch prop is theirs from the...
  7. reiddo1

    NO TACH READOUT OR CHARGING

    My boat sank last week. After running the engine in my driveway with a full can of Seafoam mixed in a gallon of fuel I took her on a sea trial yesterday. The engine, a 2000 Johnson 150 Oceanpro, ran quite well, but I am getting no tach readout from a new tach and new engine to remote control...
  8. reiddo1

    Propeller Comparison

    If an engine with a prop 14.5 by 19 pitch at wot gives 4900 rpm, what should I expect if I replace that prop with a 15 by 15 pitch? All replies are appreciated.
  9. reiddo1

    150 hp johnson Oceanpro Fuel Economy Improvement

    I have a 2000 Ocean Pro 150 hp engine which I could not be happier with except for fuel consumption. At cruise on a Glastron v216 with 25 gallons of fuel and one passenger, I calculate fuel burn at 2.5 miles per imperial gallon. While I realize that is about typical for this engine, does anyone...
  10. reiddo1

    2000 johnson 150 oceanpro gearshift cable adjustment

    I can currently by adjusting the trunnions on the gear shift cable get reverse gear with the propeller locked in both directions but only with forward locking in one direction. Conversely if I continue adjusting the trunnions, I can get propeller locking both ways in forward but not in reverse...
  11. reiddo1

    Which prop gives higher rpm?

    Mounted on the same engine and operated under the same conditions, which prop gives greater rpm.......a 14.25 dia and 19 pitch or a 15 dia and 15 pitch?
  12. reiddo1

    Proper sheeting to use for seat supports.

    My Glastron Sea Fury 216 has console seats with aluminum bases mounted directly to the floor and pipes approximately 30 inches long between the base and the seat. In rough seas there can be considerable flexing of the seat/pipe/base arrangement and in order to cure that I intend to make a...
  13. reiddo1

    Cavitation plate height vs wot rpm

    I have a 2000 oceanpro 150 hp and at wot the maximum revs are 4,800. I noticed recently that the cavitation plate is at least one inch lower than the hull. Can anyone relate cavitation plate height to maximum rpm's ? The propellor is one recommended for the motor and according to Piranha...
  14. reiddo1

    1928 Johnson SeaHorse 8.1 hp

    I have an 8.1 hp Johnson Sea Horse which according to the serial number is a 1928 model; I have tried to get a shop manual for this engine to no avail by checking the vintage outboard web sites. I have had it running but would like to ensure that it is restored to like new condition. This...
  15. reiddo1

    Counter rotation oceanpro 150 hp

    I have a newly acquired 2000 Oceanpro 150 hp with a counter rotation bottom end. The Clymer shop manual I bought covering this engine indicates that it is not recommended to operate one engine with counter rotation. I gave this engine a short trial on my boat and must say I was quite...
  16. reiddo1

    Johnson Seahorse OKL 15 or 75

    I was just given a Johnson Seahorse model OKL 15 or 75 (hard to make out the second last digit. The motor was made in Peterborough, Canada but it is spelled as Peterboro on the flywheel cover. It hasn't been running for at least 20 years but I managed to get it running in a barrel today. I...
  17. reiddo1

    2000 Ocean Pro 150 hp carburetor nipples

    On the intake manifold side of each carburetor is a brass hose nipple with no hoses connected to them. I acquired the engine this week and was told that the VRO system had already been disabled. Is it possible that these nipples which by the way are horizontal and point forward are associated...
  18. reiddo1

    1979 200 hp evinrude 4000 rpm max

    My 1979 200 hp evinrude will not turn up more than 4,000 rpm at wot. Butterfly plates in the carbs are straight across at wot, plugs are burning correctly with a tan deposit, and the prop is a 14.25 inch with a 21 pitch, which I believe is one of two props offered for that year. Boat speed at...
  19. reiddo1

    1979 200 hp evinrude trim out, works trim in doesn't

    My 1979 200 evinrude will trim in but will not trim out. I have 12 volts on the large solenoid terminal connected to the in-line fuse and 12 volts on the small terminal that the 2 black wires are connected to, but only have 4 volts on the small terminal the blue-white wire connects to. If I...
  20. reiddo1

    1979 Evinrude 200 hp V6 Foot vs 1996 Johnson 150 hp Vindicator Foot

    My 1979 200 hp V6 is grinding in reverse; I have tried adjusting through the remote control cables with no success. With the motor stopped and with the selector in the reverse position, turning the prop by hand will actually turn the flywheel most of the time, but some times it will slip. On...
Top