Search results

  1. B

    Adding A Stern Mounted Trim Switch

    I'm going to add a trim switch closer to the outdrive for convenience. My swim platform has two hinged compartments, one contains the ladder. The other one is where I think I'm going to mount it, as it is directly over the trim pump assembly in the engine compartment. My question is.....what...
  2. B

    Alpha I Gen II Impeller Replacement

    I have a couple of questions for the experts here. This is the first time I have replaced the impeller on this outdrive. While removing the lower unit, I found that the front mounting bolt had red loctite on it, not sure why. After removing the lower unit, I found that there was no water seal...
  3. B

    Best Brand Of Storage Cover???

    Several years ago I had a Taylor Made storage cover for my first boat, used it for six or seven seasons, never had any issues with it. For my current boat I bought Westland with the Sharkskin material, but it does not do a good job of keeping rain water out. I have a support system that keeps...
  4. B

    Mercury Flo-Torq II Locking Tab

    How many times can the washer locking tabs be bent before they break? Or is this even an issue when changing props? I would like to have some spares on hand just in case. Anyone know the part number for the locking tab??
  5. B

    Accurate Horsepower Figures

    I am trying to determine an accurate or realistic horsepower rating for new prop selection. My boat is a 2007 Larson 208 LXI, originally came with the 5.0L Mercruiser 2bbl TKS. Searching around I find HP ratings for the original setup from 220 - 270. Original owner did not drain the engine one...
  6. B

    Anyone Have Experience With A Solas Rubex Prop??

    Wanting to switch from the stock 3 blade to a 4 blade prop for a better hole shot. Boat is 208 Bowrider, 350 Vortec, Alpha 1 outdrive, 5150 WOT. Prop that is currently on the boat is 14.25 x 21. Thinking about trying out the following 4 blade 19 pitch...
  7. B

    Vortec 5.7 Intake Manifold Sealing Recommendations

    I pulled the intake manifold off of this replacement engine because there was an oil leak on the rear which I traced to the seal between the manifold and the block. Once it was off there was about an 1/8" gap between the bead of silicone and the gasket. Pretty sure that is my culprit as the...
  8. B

    Shift Cable Bellows Replacement

    I am in the process of replacing this and want some advise on the best way to seal the new boot to the transom. Is the Quicksilver adhesive the way to go or would any marine grade sealant work?
  9. B

    Idle Issue - Carb or Fuel Problem??

    Although I am sure this topic has been discussed before, I have searched the forum and still have questions. My problem is an erratic and unstable idle with this 5.7 2bbl motor. I purchased this boat in December at which time the tank was half full of unknown fuel. I added enough marine Stabil...
  10. B

    Seat Repair Suggestions 2007 LXI 208 Seats

    The Milsco seat inserts on both the captain and mate's seats has come apart on this boat. The foam has separated from the plastic frame. It looks like to me that either the foam has swelled, the vinyl/plastic outer covering has shrunk or a little of both. Has anyone experienced this same problem...
  11. B

    Proper Engine Oil Level

    Okay, I'm trying to figure this one out.....the original motor was a 5.0, replaced with a remanned 5.7 Vortec in 2012, unsure of the actual year of the replacement engine. The little bit of maintenance that I have done in the few weeks that I have owned it tells me that some parts were swapped...
  12. B

    Timing Adjustment 5.7 Vortec Slow Crank

    Just bought a 2007 Larson LXI 208, originally a 5.0 2bbl, now has a remanned 5.7 2bbl. Starting out with basic maintenance trying to eliminate a slow crank. New battery, cleaned or repaired all connections to switch and starter. Checked base timing at idle = 16-18 advanced, grounded ignition...
Top