Search results

  1. D

    Power head swap

    Hey Guy's, I'm going to be doing a power head swap,ona 1992 Evinrude 9.9 ,my question is,will a 1977 9.9 power head interchange with my 92? I know the ignition components are totally different, carburetor is different,but other than that,will it work?
  2. D

    Power pack recommendations

    Hi All,I have a 1977 Johnson 15 HP, think the power pack is going out,it'll run for 10 minutes or so and shut off,new coils, plugs,is there any good quality power packs, besides OMC or Sierra? Any advice would be appreciated
  3. D

    59 golden jubilee 5.5

    Hey guys ,Im having an issue with my 59 Evinrude 5.5 , shifting,it goes into reverse and neutral,fine but don't stay in fwd gear, unless you hold the shifter,I replaced the shift rod,clutch dog looks fine,the cradle looks decent ,gear set is in good condition,the spring for the shift rod is not...
  4. D

    Leaking Carrier bearing

    Hey guys, I've been working on a 79 Johnson 15 HP,did a tune up ECT,new gear case seals,but now it's leaking on of bearing Carrier,and I'm not sure why,any suggestions or tips ,I'd greatly appreciate it
  5. D

    Temp control/sensor

    Hi guy's,I bought a 75 Evinrude 15hp and this was attached to the power head, I've never seen anything like this,just curious if anyone knows what it is and what it's function is ? I've taken it off ,it was attached to a 4 or 5 pin connector,just curious that's all
  6. D

    74 Evinrude 9.9 recoil

    Hey all ,have a question, I removed the starter recoil to replace the rope, the recoil spring has unwound,how do it retention the spring,and keep it all together and be able to put the recoil assembly back in the motor?
  7. D

    Evinrude 9.9 lower shift rod

    Hey guys ,I'm working on a 1974 Evinrude 9.9 ,seals carburetor kit ECT,I'm having trouble getting the lower unit back in and shifting properly,I've measured the shift rod height according to the manual,I tried this multiple times,is there something I'm not doing or what,any advice would be great
  8. D

    Clutch dog

    Hey guys ,got a question,I'm working on a 69 Johnson 20hp, resealing the gear case, I'm not sure which direction the clutch dog goes ,it's smooth on one side and the other side is grooved , meaning the face side that engages with the fwd and reverse gear, tried uploading pictures to no avail
  9. D

    Torque values

    Hey all , replacing my reeds on my 71 Johnson 25 HP 25rl71s , what's the torque for in intake manifold bolts,and is there a proper sequence? My seloc manual doesn't specify intake manifold torque values
  10. D

    Idle issues

    Hey guys,I'm stumped on what's going on with my 71 Johnson 25 HP, I've rebuilt the carburetor with a OEM kit,new fuel pump, lines, ignition system rebuilt,new low speed needle,it won't idle down,will run with the magneto lined up with the 2 marks ,but when I lower it past there it dies,I've...
  11. D

    Water tube

    Hey y'all, question,have a 75 Johnson 25 HP, long shaft ,doing conversion to Short shaft,can the water tube be cut to fit or has to be replaced? If it has to be replaced,does the power head need to be removed? Also 68 evinrude 18 HP carburetor slow speed needle is loose even after rebuilding,it...
  12. D

    1984 Evinrude 15 HP

    Hey guys, I've got a question, my opinion bearing went out of my gear case I removed it by pulling it out, but my question is do I install it through the bottom or do I press it in through the top of the housing down towards them gear case? Is there anything else that I need to know to complete...
  13. D

    Shift rod length

    Hey guys I have a 1984 Evinrude 15 horse e15ecrm, I'm wanting to do a conversion to a short shaft,this o e is a long shaft ,does anybody know what the length of the short shaft lower shift rod should be?
  14. D

    Excessive smoking

    Hey guys, got a question my 1971 Johnson 25 horse seems to be smoking more than it should, the oil mix ratio is correct it also seems to be loading up when it idles pulled the plugs they look like it's running a little rich, carburetor rebuild with a Sierra kit new fuel pump new plugs, I realize...
  15. D

    OMC connector

    Hey guys,I've got two of these connector's, that came on an Evinrude 18 1967,and a 71 Johnson 25hp , anyone know what the part# is and what there worth, couldn't find any information
  16. D

    OMC tank color

    Hey guys,just acquired a 6 gallon Omc metal fuel tank, going to restore it,but uncertain on the color,it's from the late 60's-70's who makes a spray paint that would be the same or close enough color? Know vintage outboard paint has it but it's pricey.
  17. D

    Carburetor bushing

    Hey guys, I've got a 1967 Evinrude 18 horse doing a rebuild on the carburetor, my question is has anybody ever dealt with the bushing that the low speed needle screws into coming out, part # OMC 0303947, screwing the low speed needle in noticed it wasn't getting any tighter the bushing was...
  18. D

    Broken low speed needle

    Hey guys ,looking for some advice I've got a six horsepower 1971 Johnson ,somebody has broken the low speed needle off in the orifice wondering if anybody's got any tips on how to remove it, you can see the tip of the needle inside the hole where the Welch plug is and if you look through the...
  19. D

    Hood replacement

    Hey guys, I just bought a 1971 Johnson 6 horse, model #6r71g, it didn't have a hood on it when I bought it I'm wondering what years Hood would fit that looking for one, appreciate any information.Jim
  20. D

    Hub repair

    Hey guy's,I'm wondering if anyone has tried or has fixed a spin hub ? I'd like to try to repair mine off my 25 hp Johnson,if so what types of adhesive would one use,and the prep steps,I can get a new propeller for around 80$ but thought I'd give this a whirl
Top