Search results

  1. J

    1999 Johnson 40hp Water Temp Light

    Yes I have an OMC service manual. I'm not getting any bad tests with the stator or the new power pack. I pulled the stator today and don't see any melting from it as I was told to look for. Could the stator be the problem once it gets hot? I don't want to be a parts changer, but so far my...
  2. J

    1999 Johnson 40hp Water Temp Light

    I dropped my infrared thermometer, need to get another. But I can put my hand on the block and it isn't hot. Yesterday I took it out on the water and ran great for a a few minutes, then the water/temp light and buzzer start along with the surging, S.L.O.W. mode. I removed all sensors and...
  3. J

    1999 Johnson 40hp Water Temp Light

    My 40hp runs great and then the system check water/temp light comes on and bogs down. The impeller and thermostat are both new and looks like great water circulation. I unplugged the temp sensor and the problem remains. What should the temp be on the block/thermostat housing be? The water coming...
  4. J

    1985 75hp Fuel Pump

    What holds the spring part #6 in place? I've never rebuilt a triangle pump and I have it in pieces.
  5. J

    Ignition System swap newer 70hp to older 75hp

    It's an old timers boat. He had a used power pack installed, didn't last long. He had a new power pack put on by the same shop and same outcome. I did an ohms test on the stator and timer, both test bad. Timer shorted to ground.
  6. J

    Ignition System swap newer 70hp to older 75hp

    Is it possible to swap ignition System...stator, timer, power pack...from newer '91 70hp to older '78 75hp and run?
  7. J

    1985 75hp Fuel Pump

    Is there any option for a new replacement for a triangle fuel pump Mercury 73434A 5? I don't think I'm getting the spring and end cap put together the right way. I have an old repair manual that doesn't show the spring. Any and all help is greatly appreciated.
  8. J

    Mercury 1996 25hp remote to tiller

    Is there a kit to change a 96 25hp remote to tiller or a parts list?
  9. J

    Mercury 150hp External to Internal Hydraulic Assy.

    Can it be done with these parts in the pics or does it also need the driveshaft housing?
  10. J

    Mercury 150hp External to Internal Hydraulic Assy.

    Is it possible to change out a 1983 external trim pump on a 1983 Mercury 150 to a newer hydraulic assembly between the transom brackets?
  11. J

    1978 9.8 Overheating

    I have it in a 55 gallon barrel with at least 6" of water above the impeller.
  12. J

    1978 9.8 Overheating

    All new gaskets including the spacer that isn't plastic anymore. Still not pumping water right and gets hot fast.
  13. J

    1978 9.8 Overheating

    Can't get water to flow through it properly. It starts and runs great, but the tell tale spits out water and gets hot. I've hooked up a water hose directly to the water tube, without motor running, and it will not run through the motor and out the tell tale. Most of the water comes right back...
  14. J

    1978 9.8 Overheating

    I've seen worse. This is a friends "pond" motor. We've spent too much time on it, but it is one of those sentimental things.
  15. J

    1978 9.8 Overheating

    I have the factory replacement 23-13127 - Spacer. Is it to be installed as the picture is or the flat side towards the block?
  16. J

    1978 9.8 Overheating

    Is it part 10 in this diagram?
  17. J

    1978 9.8 Overheating

    I have a 1978 Mercury 9.8 that is overheating. I installed a new Mercury water pump kit and still spits water, clearly exhaust is coming out of the tell tale. Compression is good and equal. With lower unit removed I can send water up the tube and it immediately comes out the two exhaust holes...
  18. J

    Mercury 9.8 No Water From Tell Tale

    The little bit of water that water that came out.
  19. J

    Mercury 9.8 No Water From Tell Tale

    Yes I have, some get more than others. I haven't let it run very long the couple times I did the water spit out and was screaming hot.
Top