Search results

  1. I

    Bulkhead Stress Crack Repair

    Sorry for the delay in the reply, it will be a few days until I can get back to the boat for the additional pics. Mike, everything I had read recommended the bulkhead is cut to fit with a slight gap everywhere it meets the hull. When it's attached there is a softer material placed such as...
  2. I

    Bulkhead Stress Crack Repair

    These are pics from when we bought the boat. At first I thought they were impact cracks but then a fiberglass guy was looking at our neighbors boat and I asked his opinion and he said it looks like the bulkhead is setting right against the fiberglass on the back side and creating a hot spot on...
  3. I

    Bulkhead Stress Crack Repair

  4. I

    Bulkhead Stress Crack Repair

    I’ll post pics tomorrow
  5. I

    Bulkhead Stress Crack Repair

    Hey all, we have a new to us 2007 Cobalt 282 with twin 6.2s. The interior is in great shape but the hull has some wear and tear that needs attention. I have done some gelcoat and fiberglass repairs on our other boat but this issue is new to me. On the hull in the same spot on both sides...
  6. I

    Mercruiser B4S Conversion

    You should try surfing if you ever get the chance! It is nice and easy on your joints and an absolute blast!!
  7. I

    Mercruiser B4S Conversion

    Thanks for the info all, I will give tech support a call. I did see that the draft is deeper and that you can’t trim the drive up as high as our B3. The good thing is that the lake we boat on is deep with very few shallow areas and the boat sits on a lift so we don’t trailer it any more. I...
  8. I

    Mercruiser B4S Conversion

    Hey all, We have a 2007 Four Winns 260H that we love and is in great condition. We also have surfed a coupke of times and love it! With the release of the forward facing Bravo 4 how easy would a swap for our Bravo 3 be? Anybody know if they use the same transom assy?
  9. I

    2003 Four Winns 260H Port Dash Shroud Removal

    Hey all, the port dash shroud on our 2003 260 Horizon is cracked between the two “glove” boxes. I am going to take it off to repair it but I am not sure how it comes off. I know there are rwo bolts behind the upper glove box but not sure of anything lower. It looks like there is a removeable...
  10. I

    350 Mag MPI Questions

    All, I have a 2002 Four Winns Horizon with a 350 Mag MPI (OM254958) and a Bravo 3 drive. The past couple of times we have been out the engine has been hard to start after its been running. So I did some searching on possible causes to see if I could check a couple items and noticed that some...
  11. I

    2002 Four Winns 240H Floor Support

    All, We have just purchased 2002 Four Winns 240H and I have a question about the support structure under the bow section flooring. When you step on the floor in the center of the bow section there is about a 1/2" of flex in the floor. I have checked the deck on either side in the storage...
  12. I

    Mercruiser 5.7 Momentary Engine Cutout

    I have a 1995 Crownline 225BR with a carbureted 350 Mag engine, Thunderbolt V ignition with knock sensor, and an Alpha 1 Gen II drive. I have an occasional situation where the engine will act like the key has been shut off for a split second and then immediately return to running fine. This...
  13. I

    Starter or timing issue???

    Here is the background....Bought a 94 Crownline 225br with a rusted up engine due to the plug being left in it, serial #OF354207. Rebuilt the engine, new fuel pump, and rebuilt the carb. Finally got it started after getting the distributor lined up correctly. Brought it up to temp, oil...
  14. I

    Upholstery help

    Re: Upholstery help sorry...here are the pics
  15. I

    Upholstery help

    I've been lurking here for awhile trying to soak up as much knowledge as possible for my upcoming interior work. I have seen lots of examples of seats with piping but few without. Below are some pics of the sunpad and rear seat back for my 1994 225BR Crownline that I need to redo. I have a...
Top