Search results

  1. T

    1985 75 hp mariner wont start

    I found this in my manual .... So here's my game plan, rebuild the carbs , rebuild the fuel pump, replace the fuel lines, hopefully get it running then reinspect the plugs. My previous engine leaked from the exhaust cover gasket which resulted in water in all cylinders very obvious , this is a...
  2. T

    1985 75 hp mariner wont start

    I purchased a new to me mariner seems to be fresh water only engine. Anyway I took it for a quick spin after I mounted to the boat, it idled fine and ran fine for a little run of about 75 yard then it sputtered and stopped. I tried a few times to crank the engine but could only get the engine to...
  3. T

    Block / Cylnder head cleaning

    So I found my overheating issue, it still ran a little hot after new water pump, thermostat, popit valve, etc. . I was able to remove the exhaust jacket and the head with no broken bolts .:) :):)Apparently this job has been done before with anit-seize on the bolts ! So my question is what is the...
  4. T

    1996 85 yamaha tilt cylinder

    So the question is if I can get this off is just the top cap and seals replaceable? From the parts blow-up it appears you have to change the whole unit. I maybe doing manual tilt yet again !!!:mad:
  5. T

    88 johnson 20 water jacket gasket removal

    I need to put my thermostat back into the head. I have a brand new gasket on the jacket now, but when I removed all of the bolts the jacket did not separate from the head. What is the best way to get the jacket off ? I am thinking about using a long scraper type razor to split the gasket down...
  6. T

    does anybody have any ideas for obsolete head bolts ?

    I need head bolts for 20hp johnson part # 0395027 will 0305027 work ? I hope I am posting this in the right place. I have searched and called high and low for these bolts. Does anyone know a part alternative since the head and crank case can be used for 20- 35 hp ?
  7. T

    88 johnson 20 new cylinder head assembly questions

    I am in the process of replacing the cylinder head. I was hoping you guys could help with a few questions. #1 what if anything can be done about the hairline crack I found (see photo) #2 can and should I use emory cloth to clean the block mating surface where the gasket goes #3 do you use...
  8. T

    Tohatsu shift shaft seals

    I just bought a 92' lower end that does not have any known seal leaks. I was wondering should I go ahead and change the inner and outer shift shaft seals or leave well enough alone. Thanks Brian
  9. T

    M60a bevel gear b

    If I can find the bevel gear b for this engine can you simply replace the gear? I know the service manual recommends you replace them all but if I can get a few more trips out of the lower end by only changing the b gear, I think it would be worth it. My b gear has a few pieces of the teeth...
  10. T

    tohatsu 86 M60A lower unit compatibility

    Does anyone know the various lower units that fit the M60A ??
  11. T

    tohatsu m60a wont go forward

    Got boat in water at ramp. After letting engine idle nicely for a few minutes the boat would not go into forward. I could get it into reverse. I verfied that the choak was down,then reversed back to the ramp. Anyway I get home and put it in the barrel. I notice that the out most shift linkage...
  12. T

    78 4hp do recoil spings wear out or can they be oiled ??

    My recoil spring will not pull back the cord very well. If you tug the cord a little it want's to recoil but will not pull the cord all the way back in.
  13. T

    4 hp gnat impeller change now wont go in gear

    I removed the lower unit then replaced the impeller. Put it all back together and now putting it in forward or neuatral does nothing. The rod that comes from the hift lever is going in a hole right around the water pump. I dont see a way to get at the gear from the top. Kind of at a loss for...
  14. T

    help 4 hp water leaking around top spark plug

    Is the bad or is it just a seal that needs to be replaced
  15. T

    4 hp 1978 where is the p hole ???

    I just bought this outboard and have finnaly got it to run for a few mins. I was wondering where the water from the pump is supposed to come out I cant find it anywhere.
Top