Search results

  1. mick97

    1987-125hp force seems to bog down some.

    Hi everyone. I took the kid out tubing the other day,and seems to bog down on turns.. Seems to go ok straight ahead,and i know turns can slow it down,but seems to bog down.. Starts hard,and dies unless i put it in gear right away,alot too. Going full speed is ok for awhile,then i have to let up...
  2. mick97

    (Diamond) black box under dash in 87 bayliner

    Hi all, Can someone tell me on the boat i just bought,what the black box that says diamond,under the passengers side is? It some type of control center im guessing..Alot of wires going to it. Thanks, Mick
  3. mick97

    Setting the jet screw

    I just got a new head gasket on,and all is well :) I did mess with the jet screw a little when i was trying to figure out what was wrong before. I know its like 1 1/2 turns out its suppose to be.If I go to 2 full turns out,that uses more gas correct? No biggy.But was just wondering if it will...
  4. mick97

    Force Gasket Help

    I have a bayliner 1989 with a 50 force.Black and pinkish motor cover.No engine tag. I have no a=b-c or anything. I bought this as the guy told me it would work. Mercury Chrysler Force 50 55 HP Head Gasket 27-F658529-1 18-3854 Hole pattern was correct on it,as i ordered one here in town,and the...
  5. mick97

    Force 50hp 1989 torque?

    Is the torque 50 lbs on a 50 hp force motor?For the head gasket? Thanks :)
  6. mick97

    Force 50hp 1989 year made tag

    Where do you find the tag on the year a motor was made? I was told it should start with some A's or something.I cannot find a tag on the outside of the motor,or any place on the inside. Assuming it is a 1x2 tag.. or something. Looked all over inside the motor as well.Just some stamp markes on...
  7. mick97

    Force 50hp 1989 timming place

    Where is the timing screw located on a 89 50hp force? Does anyone have a picture? Icant seem to find it.its the one with a black hood cover if that helps.
  8. mick97

    1979 force 50 hp tune up

    hi,I have a 79 boat and motor on a 14.5 foot bayliner.What is there to a tune up? It started running sluggish over the summer..Someone said it dont have points,and another says it does...If it does,that sure seems to fit hte prtoblem of getting slower..Everything else has been...
  9. mick97

    force 50 hp start,run problems-timing?

    Hi, I got a force last yeay,and it had a 50 hp on it. Ran good.Twards fall,it died a couple of times. This year it starts hard usually,but once i get it running,it runs,but doesnt seem to be as fast. Heres the deal............ I start it and go about 5 mph around the lake.Runs fine slow..Top...
  10. mick97

    Force 50hp tune up question

    I have a 1989 force.the black cover with blue writing.It studders a little. What all is involved in a tune up on these motors? I also might want to time it.Where do i get access to the timing? My old 85 force had a spot under the flywheel to set.So not sure on this one where to set timing.I did...
  11. mick97

    50 force serial number?

    I cant seem to find the serial number anyplace. What year did they make the motors that are black,blue stripes,and the (50) is blue? That might help in telling me it is a 89,as the boat is.Or not lol It is a 14.8 open bow,has cfi on it,crossfire fuel injection,us marine power. The boat is a...
  12. mick97

    50hp force coil packs

    Im thinking about buying an 88 bayliner outboard and was wondering what the cost is approximately of a coil pack. It has a force 50 hp,and they said his dad works at a marine shop.He said its #1 coil pack.. Anyone have a ball park figure on cost on this,and where to get one? Thanks, mick
  13. mick97

    88 bayliner coil pack?

    Im thinking about buying an 88 bayliner outboard and was wondering what the cost is approximately of a coil pack for it. He said it needs one,so I wanted to find a pricing to see if it is worth my time. Also where can I order one? Thanks, Scotty
  14. mick97

    88 galaxie omc 4.3 thermostat question

    Hi, I have a omc that i just replaced the water pump in. I had it in the lake and it heated up to 180,then cooled down just fine. Was just tooling around for 1/2 hour or so. Then i kicked it down,and all was well. But all of a sudden it heated up and i had to turn it off. Put in drive...
  15. mick97

    1988 galaxie boat weight?

    I have a Galaie 88 i/o. Im looking for a boat lift,and needed to know the weight of it approximately. Does anyone know what the weight of it might be? Its a 17 foot. Thanks, Scotty
  16. mick97

    omc motor plug?

    Re: omc motor plug? I don't know what a surround is,but im guessing its a smaller inner hole or indented circle. It looks like a 50 cent piece will fit in there nicely though,and the backing will keep it in tight,then jb weld over it. Should be almost flush then :) Should i just go over the...
  17. mick97

    omc motor plug?

    My motor is over heating. I put it on muffs,and water was pooring out the side. Found out this plug fell out. I looked in the manuel,but cannot find a name for it. Does anyone know what this plug would be called? See picture 1-the other side of the motor has a plug in it with omc written on it...
  18. mick97

    fuel pump omc 4.3 87/no fuel

    Hi, Question on the fuel pump. I took out the fuel pump and thought i cleaned it,but when i go to choke it by pulling out the throttle and pumping it,nothing is going to the carb. Was thinking big deal at first because its only the choke and i can put gas in the carb to get it going,and work on...
  19. mick97

    87 omc 4.3 timing question

    I have a 1987 4.3 omc galaxie boat. I haven't done this for a long time and need some help. Where are the timing marks located? I believe someone said 6 degrees for a 4.3 correct? I put a clamp on the positive of the coil correct?And then clamp over the #1 plug wire correct? Looking at the...
  20. mick97

    Setting points/dwell

    I have a question on setting points. I will have points and condenser on wednesday. I haven't worked on points for a long time. What would be the dwell to set them at on a 4.3 omc 1987? Its a 1987 galaxie boat. Im thinking its around 47? So basically I would turn the shaft to its highest...
Top