Search results

  1. Y

    2005 5.0 GXI Volvo penta crank but will not start

    Check the pressure regulator. When I first got my current boat (same engine) it had also been sitting for many years. Regulator was so clogged with those paint chips that it threw the fuel pressure through the roof - essentially insta-flooded the engine and crank crank crank no start. Also...
  2. Y

    No fuel - check my work and add as needed

    You seem to be going about it the right way. My only question is, are you positive it's not getting fuel or is that more of a hunch? Reason I ask is, a stuck choke could lead to similar symptoms (starts fine cold but dies warm). Especially right at about the 2 minute mark like you're seeing...
  3. Y

    Overheating 5.0GL-E with SX-M Outdrive (2004)

    If you're on muffs and engine isn't running, water won't come out below at the transom. That will only happen once the engine starts and then impeller draws the water through. When you inspected the seal on the drive, did you also check the oring on the feed hose? The hose that connects to...
  4. Y

    Volvo Penta 5.0 gxi intermittent starting issues

    Sounds similar to my issue too (and my thread just below yours). I'll be cleaning the MAP sensor this weekend.. but also thinking the IAC might be suspect. It's just strange though because once it DOES start, it's good to go. All major systems inspected/replaced (pressure regulator, fuel pump...
  5. Y

    Diagnosing an issue - Question about IAC

    Hmm well, the engine compartment is pretty darn clean, and it's very low hours (about 70) - BUT - I'll still check it! The engine sat for YEARS before I got it and got a bunch of mold in the engine bay. She's spotless now but, I'm wondering, if that device got some crud on it in all the years...
  6. Y

    Diagnosing an issue - Question about IAC

    Hello everyone, I have a question about the IAC. Is it a device that can be "going out" or is it a binary "working" or "not working" type of thing? I've been dealing with a set of symptoms for about 2 years now that I can't quite crack. Specs: 2004 Larson 212LSi 2004 Volvo Penta 5.0 GXi...
  7. Y

    Hard starting after sitting for a few minutes

    Can you give us the actual model of the engine? For instance, 4.3 GXI? (displacement plus the letters after) Need to understand if we're dealing with a carb'd, throttle body injection or port injection situation.
  8. Y

    trailer manufacturer picks?

    Steel painted for me. I like the idea of galvanized, but, to me, they just don't look good. Looks junky to me, even new off the lot - I know that's not actually the case (just the opposite) - but their looks don't lend credibility to the quality. I prefer a trailer painted to match the boat...
  9. Y

    Idler pulley options

    Anybody know of any alternatives to this part: 4.3 idler pulley (3861009) http://www.volvopentastore.com/…/cart_id.355948480--session… (#10 on the diagram) I know these can be found for GM trucks for $20-$40. Looking for a cheaper, and also more readily accessible, version of the VP part...
  10. Y

    VEC Hull - % of Fiberglass

    Hi - I'm looking to purchase a 2004 Larson 212 (some pics attached - it hasn't been cleaned up yet.) Boat has very little use, has sat most of it's life. Problem is, at one point the tarp blew off and the owner didn't realize it. Plug was in, so boat filled with water, not over the deck...
  11. Y

    1994 Volvo Penta SX w/Ford 302 - Trim tilt & Trim question

    Hello. I just bought a 1994 Wellcraft Eclipse 196s. Motor and outdrive seem in good condition, however the hydraulic tilt in trim system slowly leaks down as you drive around the lake. One shop is giving me the 'doomsday news' saying it could be leaky lines, a leaky metering system, etc and...
  12. Y

    Need help asap!! Stranded at lake! (ignore - made it home)

    1996 evonrude 115 60 degree. Working fine. I go to start to head to docks.. Nothing. No power. Got back to doc w/troller. Now can't get motor up because no power! The whole system is totally unresponsive. Help!! I tried this 'manual release' screw but I can't pull the motor up more than...
  13. Y

    Can someone look up this TM model number please?

    Hi all - Below is the model number of my trolling motor, but can't seem to find any specs about it: It's branded Evinrude: BF4TPV Any help appreciated!
  14. Y

    Quick Breaker question

    Hello, I have a ranger boat - the trolling motor terminal has two 12v lines going to it. The trolling motor bridges them internally. I know typically for a 24v trolling motor you get a 50amp or so breaker. Seeing as how the batteries are not in series in this configuration.. do I still need...
  15. Y

    Which seat base goes with this post?

    Hi all, I'm going to be getting one of those small seats you lean up against for the deck of my bass boat. This is the post I'm going to use: http://www.basspro.com/Springfield-Kingpin-Adjustable-Pedestal-Post/product/22450/71981 Can someone send me a link to the base that's supposed to go...
  16. Y

    Need help finding a part

    Hello, Was out fishing a few weeks ago, and while trimming my motor, the switch on the speed control lever that controls the trim broke. Basically I was on plane, and using my thumb on the switch to trim up. Out of nowhere, the switch pushed "in" to the controller (like a piece of plastic...
  17. Y

    Question about tank venting

    Hello all, I purchased a ranger clone (1997 "Ruffneck" - 16' bass boat built in Zimbabwe and based off a ranger design. Don't ask me how the previous owner got it to the US). Boat has a 115hp Evinrude. I was in the middle of replacing all the lines going to the tank when I came across a bit...
  18. Y

    Oil and Fuel lines ?

    Hello, I have a 1997 evinrude 115. I recently noticed that I was getting a bunch of junk in my fuel filter. Originally thought it was sediment in the gas tank but upon further inspection, it looks like the interior of the fuel line from the tank to the motor is breaking apart on the inside...
  19. Y

    How to adjust shift cable

    Hello, I have a 1997 BE115GLEVA I've had the motor for about 2 months now. Runs good, but I've noticed that the shift linkage is off. When I go into reverse, then back into neutral (on the controls), the motor stays into reverse until I go like 1/2 inch into forward, then it kicks into...
  20. Y

    What's with the constant bad reception I get from service shops?

    It's getting a little annoying. Whenever I call to get a quote and tell them I have a 60-degree evinrude, they say, "stop right there, you know about the issues with that engine right?" "What issues?" "Overheating issues, sputtering from carbon buildup, and the recall" "What recall?" "The...
Top