Search results

  1. the454assassian

    New transom pod install

    So I got a new transom pod rated to hold my motor since the last one wasn't and we had a failure. Since the new pod is alot stronger than the old one and larger. Should I move it back some the the engine is further away from the boat? And my next issue is the motor mounting, since the bottom of...
  2. the454assassian

    Loud rattle/banging noise

    I am helping out my cousin with his boat. He let a friend store it over the winter as long as he could use it from time to time. Needless to say the boat was not returned in the same condition. Blown fuse on starter, tripped breaker on motor, fuel issue either water or trash in it prop slipping...
  3. the454assassian

    I broke it

    my pontoon(24ft) had a motor up grade to a johnson 150 fast strike before I purchased it. Me and my cousin reinforced it to handle the extra weight. It did great last season and good until last weekend. When I was getting ready to put it in the water I noticed the transom looked like it was...
  4. the454assassian

    hub issuses

    one of my hubs over heated and cracked. the bearings are destroyed. How can I measure the axle so I know what to buy to replace it? http://www.southwestwheel.com/store/c-1245-hub-assemblies.aspx that is the site i am going to buy from and you can see there are several options.
  5. the454assassian

    pontoon with motor transplant

    Hey everyone I got a 24 foot pontoon at the end of last summer. I had to replace the floor on it so I didn't get to use it to much. It had a motor swap by the last owner. It is running a johnson 150 fast strike. It has a 14x24 prop on it and I am pretty sure that is not what I need for my...
  6. the454assassian

    new to pontoons

    the pontoon i just bought is 1995 landau pontoon dx-24. the PO switched out the motors from a 50 to a 150. They mounted the controls in the wrong spot so you can not go full throttle or even up to cruising cause it hits the helm. My question is should I reinforce the transom before I move the...
  7. the454assassian

    weep hole

    Hey everyone I recently got a pontoon for the family and today was the first day I took it out. While riding I noticed it started to run rough and a few seconds after I had an alarm go off. I shut the motor down and waited a minute I restarted it and resumed cruising again. Shortly after it did...
  8. the454assassian

    What should I do?

    I have an 87 eagle fish and ski 17 ft with a johnson 140. The transom has a crack and I am not not sure how to proceed. I tapped on the back of the transom and it seems solid every where else. I don't know if I should pull the motor off and the top of the boat so I can get to the transom. Or...
  9. the454assassian

    cuts off

    1987 140 vro already disconnected. When I first got this boat a few months ago I had to clean the carbs out to get it to run been sitting a while. After cleaning the carbs and fresh plugs and gas/oil mixture it runs great, until yesterday. It idles fine and revs fine with the fast idle lever...
  10. the454assassian

    idle

    How do I adjust the idle on my 1987 140? its just a touch to low
  11. the454assassian

    Stupid question

    This is the first out board I have owned. First two stroke I have owned also. I just got it and cleaned the carbs out changed the plugs and got it to fire up. Tomorrow after work I plan on changing the water pump impeller and the gear oil. My question is How do I change or can I change the oil...
  12. the454assassian

    removing from long storage

    I just picked up a 1987 eagle 371 thats been in dry storage for 3 years. It has a 140 hp on it. I know the gas is bad that is in it. I shoot some starting fluid into the air box to see if the motor was good and it tried to start. So how should I go about getting all the old gas out of the carbs...
  13. the454assassian

    controls

    Re: controls
  14. the454assassian

    controls

    Re: controls
  15. the454assassian

    controls

    Re: controls its been a while since i messed with it. thats the only pics I have of it. I will run out to where i have it stored tomorrow and try to get some more pics and info off of it
  16. the454assassian

    controls

    I have an old glass master can't tell what year it is or anything it has no hin number to old i guess. I have a 40 hp motor on it but no wiring from the from of the boat to the motor. can some one tell me what I need and where to find it?
  17. the454assassian

    Getting mad at an 888

    I have a 1974 searay with an 888 mercruiser, and it is really making me mad. I fixed my water leak and I am trying to put my stern drive back on but it will not go the last 2 inches. I have it resting on the studs and it is just shy of being able to put the nuts on the studs its taunting me. I...
Top