Search results

  1. S

    1979 bay liner liberty out drive help!!!

    Yes I read that post a few times my only concern is where the motor is located…it’s located towards the right back of this engine block and I could burly get my hands in there to remove the black cap. I can’t even stick my head in there to look at what I was doing 😢😢😭😭😭
  2. S

    1979 bay liner liberty out drive help!!!

    How do I check the motor? There is no wires coming from the motor. Well at least I don’t think. I was looking. Technically for a motor to work you need power but I don’t see exactly where there at
  3. S

    1979 bay liner liberty out drive help!!!

    Also, is the blue one the only thing in there that I can change?
  4. S

    1979 bay liner liberty out drive help!!!

  5. S

    1979 bay liner liberty out drive help!!!

    After taking apart the black box this is what’s in there. Are these the relays you guys speak of?
  6. S

    1979 bay liner liberty out drive help!!!

    Let me look into this link thank you
  7. S

    1979 bay liner liberty out drive help!!!

    Last time it work was last year when I stored it for the winter.
  8. S

    1979 bay liner liberty out drive help!!!

    Ohhh so there is relays in there?!? I took off the 3 Philip head screws but then I saw on top 2 hex screws that went all the way through with nuts on the bottom am like that’s a little over kill to be relays so I didn’t remove the hex screws. I will look into that box today.
  9. S

    1979 bay liner liberty out drive help!!!

    Good afternoon all I have search near and far with no answer. I have 1979 bay liner liberty. Engine is a Volvo penta 200c out drive is a 280. I don’t no what make. Anyways my tilt won’t go up or down or make any noise at all before it was working. I notice when my son stepped on the out drive...
  10. S

    Velvo penta does on water

    Everything turn on is running smoothly only thing I see is white smoke coming from tail pipe other than that it’s running I believe like it suppose to
  11. S

    Velvo penta does on water

    I need a new sending unit since the gas gage is not reading anything. So my plans are to change it out reguardless and I can look inside tank after replacing sending unit. But I remember looking into tank when I was diagnosing the sending unit it didn’t look to bad
  12. S

    Velvo penta does on water

    I believe the tank sat for a few years without any fuel in it. It does have a fuel filter port 2 of them actually that we did replace. But I would do whatever to keep gunk going into carb and system
  13. S

    Velvo penta does on water

    I had a friend rebuild it and he said the jets where full of debris little gunk parts he cleaned it completely all I have to clean is the flame resistor but I haven’t put it back into water just yet was changing spark plugs and I saw that each spark plug was a different gap size
  14. S

    Velvo penta does on water

  15. S

    Velvo penta does on water

    Good morning mates, Another question before I came to this forum I asked a marineboaring forum I forget what it was called but they said the gap was .025 now so I do what this forum says or what they say that’s a big gap diff in my opinion. Thank you fellow boaters
  16. S

    Velvo penta does on water

    Okay thank you so would the autolite 145 which is preset to .040 work or should I knock it down to .035
  17. S

    Velvo penta does on water

    Am sorry I just realized that it’s a 1979 volvo penta 200C if that makes a difference
  18. S

    Velvo penta does on water

    Good afternoon, I just rebuilt the carb and gonna see how it does on the water but before I put it in water I decided to change spark plugs on it. My question to any does anyone no the correct gap size for this motor? I tried to copy the old spark plug gap sizes but they range from .010 - .035...
  19. S

    Velvo penta does on water

    Anyone have anymore ideas before I take it to a marine mechanic.
  20. S

    Velvo penta does on water

    Thank you for your help. I used 2 different gauges both read the same. Someone mentioned to me something to do with the propeller
Top