Search results

  1. W

    no oil after cylinder head recondition

    Nothing hydrolocked or frozen. Engine running when i winterized it. Since the heads were redone and installed, engine was started and run with no abnormal sounds. Only issue was lack of oil coming up thru pushrods. Oil pressure was a little over 60. Lifters should arrive 4/11. I'm hoping to get...
  2. W

    no oil after cylinder head recondition

    Nothing hydrolocked or froze. exhaust valves were rusted. I have run the engine since re-installing the heads and engine sound good. It was winterized, oil changed, and raw water system completely drained. I installed 2 bilge heaters to prevent freezing temps in then bilge (theybavtually work...
  3. W

    no oil after cylinder head recondition

    I checked the lifters over the weekend. I could visually see 2 had what looked like sludge on the top of them. The others did not have any spring to them when i tried to depress the pushrod. i'm going to install all new Lifters, as opposed to trying to clean them, after, after i change the oil...
  4. W

    no oil after cylinder head recondition

    I did place the new pushrods in oil overnight. i changed the oil 2 times before taking everything apart. When I started the engine It ran for about a minute and I shut it down. I didn't want to run it any longer the way it sounded. i did not use a priming tool. I plan on doing that this...
  5. W

    no oil after cylinder head recondition

    To add some background - before engine was disassembled, it was running, roughly of course, and pumping oil up to the rockers. The engine sat for about 8 weeks before I could restart assembly. Should I have removed lifters and pumped them up with oil?
  6. W

    no oil after cylinder head recondition

    The lifters were not touched. I replaced all the pushrods since a few of them in were bent.
  7. W

    no oil after cylinder head recondition

    i have an inboard merc 7.4 gen vi (it is a 2000, but I cannot find serial numbers on either engine). I had the starboard engine cylinder heads redone after a few stuck valves, from water in the oil. upon installing the new heads with all new gaskets and bolts, i am not getting any oil to the...
  8. W

    7.4 Gen VI cylinder head gaskets

    I purchased the boat with these engines and the PO (2nd owner) knows nothing regarding the engines. Spoke to his mechanic and he has not done any work on the engines other than usual yearly maintenance. All I know, from paperwork found in the boat that the original engines were replaced in 2005...
  9. W

    7.4 Gen VI cylinder head gaskets

    I have twin 7.4's Gen VI MPI's. These were distributed by Sea Max, so i cannot find much info on them. The engine serial nbrs are unreadable. The paperwork says they were produced in 2000 and installed in 2005. I just had the cylinder heads done on the starboard engine due to stuck valves from...
  10. W

    rust on valve parts

    1990 omc 460 inboard. had the heads redone due to rusted valves on cyl 6 and 7 last year. put boat in water but had to take out due to shaft logs leaking too much, plus valves needed adjustment (discovered mechanic did a poor job). . only put 45 mins on engines before taking out. updated to...
  11. W

    raw water pump question

    My port raw water pump seized up over the winter.I have a sherwood P103. the replacement for this discontinued pump is a P105 but the mounting holes do not line up .Is there any pump out there that will have the flange mounting holes in the 12,3,6,9 o'clock positions? i have 1990 OMC/Ford 460's...
  12. W

    how to hookup power steering cooler hose

    i have twin ford 460 inboards with v-drives on a CC 340 crowne with half closed fresh water cooling.over the winter i had a mechanic start the work to swap out the old shaft logs for a dripless system. in order to make room in between the engines he removed the inside exhaust manifiolds, heat...
  13. W

    removing engine

    The packing in the stuffin g box is shot .. water comes in like someone is pouring a bucket on both shafts. the boat was out of the water for 3.5 years when i bought it. i could reach it if i had 4 foot arms and triple jointed. The the set up on this engine compartment doesn't have enough...
  14. W

    removing engine

    i have twin omc 460 inboards in a chris craft crowne 340 with hurth v-drives. the shaft packing is shot and in order to change it i need to remove the engines. there's no way you can get underneath to change the packing. is the transmission connected to thw bellhousing wiith ony the 6 bolts or...
  15. W

    Risers for OMC 460 inboard

    So i finally (after over a year) got my parts from my mechanic and put my port engine back together. What I thought was a broke timing chin turned out to be 2 frozen valve and a cam pin sheared off. Engine starts up and runs good. problem is i'm not getting water thru the risers. while...
  16. W

    no power to ignition switch

    I have marine 460 the boat is a 93. Im assuming the engines are 89 or 90. while re-doing the heads ,cam,and timing chain on one of the engines i accidently turned on the battery switch. the coil was hanging over the crank and must've grounded out . I now have no power going to the ignition...
  17. W

    distributor not always rotating with engine

    i installed a new pertronix electronic dizzy along with a new coil and newer wires and plugs. i have noticed that the dizzy does not always turn when i was bumping the motor, using the starter, to get it to TDC. i was able to get it to start one time (I shut it down since it's a marine engine...
  18. W

    Slow crank

    I have twin inboard ford 460's mated to v-drives. I brought the boat with knowledge that port engine wouldn't turn over at all. the starboard motor cranks and starts with no problem. I was able to turn the port engine by hand so proceeded to repair any thing that needed replacing including a...
  19. W

    Ford 460 fresh water cooled

    i have twin ford 460 inboards on a CC 340 crowne with full closed fresh water cooling. can anyone point me tin the direction of a daigram and/or schematic for the routing of the raw water and coolant hoses. thanks
Top