Search results

  1. S

    Prop for Suzuki

    None of the "prop finder" tool on multiple sites will give me a a prop suggestion. I have a 24ft pontoon and 115 hp 2 stroke Suzuki. Any thoughts?
  2. S

    New rectifier regulator?

    Well, it is charging nicely, and the tach is no longer erratic. Thank you
  3. S

    New rectifier regulator?

    Thank you!
  4. S

    New rectifier regulator?

    1992 75hp triple. Had some tach and charging issues. Got new reg/rec in. The wire colors match, but not their positions. New one also had ground. How to wire this thing??
  5. S

    1974 9.9

    Noticed my ol'reliable 9.9 was a little "off" today. Runs good and starts easy. Went to check points. Good. Sync is way off. Got all the adjustment out of ramp I can get. Roller is about 1 inch starboard of mark before throttle plate moves. Nothing looks overly worn. Something definitely needs...
  6. S

    Small ground strap

    E15rccs I put a new used powerhead on mine. I videoed my motors before tear down. I have a small 6 inch ground strap on block, port side, I believe mounted to exhaust cover. Do any of yoose guys know where the other end could go. Of course my video did not help.
  7. S

    More 25 evinrude hurdles

    25553b... This was a no compression project. Blown head gasket fixed. Magneto plate wobbling. Fixed. Point gap problem fixed. Gummy Carb, fixed.Now she is easy starting..Today was her big sea trial. 10 miles up river and back. And she did fine, a little lacking in low to mid range. No bogging...
  8. S

    Powerhead interchange

    E15rccs, what years can i get a used powerhead so I can just bolt up my peripherals without a hack job. Does 9.9 make a difference? Thanks guys I killed my block tonite. Broken thermostat housing bolt lead to head removal. That lead to broken headbolt. Twisted protruding remnants of headbolt...
  9. S

    Part help

    25553B..getting this one dial in. Had point trouble, bought cheap crap point set that wouldn't gap, tried used set, got them to gap. So I ordered New BRP tune up kit. Long story short was cleaning mag plate. Lost screw #8 on magneto diagram.(Long one thru driver coil that secures mag plate...
  10. S

    Water Pump

    E15RCCS. I was trying out some of my projects today. I went thru fuel system and got this engine running great. I noticed it was not pumping water. Replaced impeller. Have a few hours on it now, peeing properly. This morning I noticed minimal peeing and minimal water at ?blubber hole?.. Off with...
  11. S

    Points adjustment

    25553b/1975 25hp. I succeeded in stabilizing the armature plate. So now to resetting point. Port side went well. Loosened set screw, adjusted where .020 just drags through, tighten set screw. To starboard. Loosened set screw... ​​​​​​No matter what I tried with adjust screw most I could get is...
  12. S

    1975 25hp Evinrude

    All right gentleman, my nemesis is whipping me. The ?armature? plate wobbles like a bent rim on bicycle. She wants to run, but I can't blame her for being difficult, I bet the timing is everywhere. It does run, just hard starting and difficult to keep on. I searched my problem, tried Mr Reeves...
  13. S

    1975 25 hp throttle

    Old evinrude resurrection has gone well. One quirk however. When advancing the throttle, if you go to far, the roller can fall off the other side of the ramp( ?timer base?). What to inspect/ repair to prevent this?
  14. S

    OMC Interchange?

    1959-76 18hp & 20hp 1969-76 25hp From my novice research I do believe the cylinder head and cylinder head gasket interchange?
  15. S

    Powerhead interchange?

    1974 9.9 evinrude powerhead is toast. Will a 1988 Evinrude 15hp be a direct swap?
  16. S

    Need 9.9 carb help

    1974 Evinrude 9.9...still having high speed issues. Compression great, spark jumps a gap w/o a snap, link and sync done, carb clean and rebuilt. Tool carb apart again...this is what I saw. Need your opinions please. Look damaged and off center to me
  17. S

    Johnson 9.9 advice

    1975. Bought a few motors and this is head scratcher, for me anyway. Bought this motor complete with seized powerhead. Lower unit is good. Penetrating oil and wait. Long story short she is free and spinning nicely. Did a carb clean and kit, points/ condensers and plugs. Spark test of approx 3/8...
  18. S

    1974 9.9 question s

    Great compression. Spark that puts lead in your pencil. New coils, points, condenser, and rebuilt carb. Starts super easy, trolls and slow rides great. Try to go fast and she does it for a few seconds, loads up and slows down. Does not shut off, just quits " pulling". So I search the forum. She...
  19. S

    manual question

    Will a 1970 Johnson 6hp factory service manual suffice for a 1968 evinrude 6hp fisherman? I think yes but want to make sure. The generic leaves alot to be desired. Thank you again folks
  20. S

    More Fisherman help please

    Well after getting the fisherman running well, i as not satisfied with the intermittant water flow. So i look at you tube for lower unit removal. I watched highlander marine. Romoved four 7/16 bolts and she dropped an inch. Removed shift shaft bolt. Just like the video. The unit would not drop...
Top