Search results

  1. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

    I added the pic of the lower unit. I did not change the rod height after replacing the impeller
  2. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

  3. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

    There’s just one motor, photo of the side with the linkage
  4. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

    I adjust that using the thumbscrew in the picture, or is there another way?
  5. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

  6. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

    The prop spins freely in both directions when it’s in neutral. In the drive it locks up, in reverse it only spins one way. Is that how it’s supposed to be?
  7. GSX455

    Adjusting the drive and carb linkages on ‘89 90hp

    I recently rebuilt carbs and replaced the water pump impeller. Model J90TSLECM When I did the linkage after dropping the lower unit, I’m pretty sure I left it in neutral. Does the red circle looks about where it should be? I tweaked the upper thumbscrew, but afterwards remembered you...
  8. GSX455

    Any saving the engine? I’m devastated

    I would add some Kroil or Marvel mystery oil to the 2 stroke gas, in case of any corrosion
  9. GSX455

    Finishing before gelcoat

    I'm using Velcro on the bottom of the bottom of the boat floor, Velcro sticks pretty well. The carpet is wider than the floor. Should I trim the carpet to the floor width or run some up the sides for protection? I'm thinking the floor width trim looks better; opinions welcome. I stapled...
  10. GSX455

    Finishing before gelcoat

    What are folk’s experiences with carpet inside a boat? Good or bad? It’s cheaper than a laminate and covers up the floor
  11. GSX455

    Finishing before gelcoat

    Instead of a laminate, I plan to put carpet on top of the gel coated fabric. Just run carpet midway up the sides to the ledge in the photo above?
  12. GSX455

    Finishing before gelcoat

    Does anyone know of a laminate that you can put over Sprayed gelcoat that has the texture you see in OEM boats. It's a plastic with a diamond pattern. Something less expensive than PlasTeak? Here's the boat floor now after adding 2 layers of 1708 and then PE resin and then gelcoat with...
  13. GSX455

    1990 Johnson 90HP 2 Stroke Bogging - Help!

    I second getting another fuel pump or replace the diaphragm. It sounds like a fuel pump issue as well. Good luck
  14. GSX455

    98 Johnson leaking hydraulic fluid.

    I ordered a used Ebay tilt & trim that happened to be the same year and HP as mine. It works too! Is this a sensor switch? Mine is not plugged into anything. I could not find an unused plug on the wire harness for the boat. Anyone familiar with what this does? Thanks for all the replies; it...
  15. GSX455

    98 Johnson leaking hydraulic fluid.

    Correction; cleaned contacts in relays and the pump runs, and the trim rods will still not raise the motor
  16. GSX455

    98 Johnson leaking hydraulic fluid.

    I’ve rebuilt and replaced all of the seals and now the trim pump won’t run. It ran before the rebuild. The relays click but nothing, replace motor next?
  17. GSX455

    98 Johnson leaking hydraulic fluid.

    Thank you for replying; that sleeve inside the main tilt tube is supposed to be pulled out and has O-rings to replace with some special Johnson tool that is hard to find. I think I'll just get this running and then hope it works. If not, and that sleeve Oring is crucial, then I need to find a...
  18. GSX455

    98 Johnson leaking hydraulic fluid.

    Has anyone rebuilt the trim ona Johnson outboard? I’m trying to get the sleeve out but it seems seized in there. All other O-rings are replaced , I even tried using the sleeve tool, but this is in there Tempted to leave it in, since the leak in the trim tabs was around the piston and not the...
  19. GSX455

    98 Johnson leaking hydraulic fluid.

    Yes, exactly, tilt rams will get it up to their max travel but center ram does not extend. The rebuild kits got mailed, so the rebuild of the of all the seals starts this weekend. Thanks again!
  20. GSX455

    Adding strings to a boat without stringers

    Before I put a hole in the hull, make sure you find if polyester or 3M 5200 sticks to the hull material. A brass Gabbard plug will ensure a leak free fitting to your boat, or you can use a brass drain tube with rubber plug...
Top